manualshive.com logo in svg

Innovatech Teerminator-2000, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Innovatech Teerminator-2000 Скачать руководство пользователя страница 17

17 

TERMINATOR® OPERATION AND MAINTENANCE MANUAL 

  Blades are available in different configurations and thickness.  An assortment of blades is included in the 
purchase price of the Terminator®.  Extra blades are available upon request from Innovatech Products & 
Equipment Co., Inc.

  

 

Figure 5: Blade Assembly 

 

Installing a Blade 

 

1.)  Lower the blade assembly to maximum down position, which is two inches off the floor. 
2.)  Unwrap the pre-sharpened blades and select the blade thickness and length you need for the job. 
3.)  Loosen the 7 holding bolts. 
4.)  Insert the sharpened blade. 
5.)  Tighten bolts firmly, starting from the center and working out.  Bolts should be snug but not over 

tightened.   

 

Adjusting Blade Tilt 

 

  Loosen the blade angle adjusting bolt and manually move the blade to the desired tilt (angle is set at factor for 
80% of the job); tighten the bolt.  Raise the blade assembly a few inches to clear the floor and prevent damage to 
the blade while the Terminator® is in transit. 

 

Taking Up Floor Coverings 

   

1.)  Insert blade. (As shown above) 
2.)  Lower blade to floor.  As the blade flexes lift caster wheel off the floor ¼ inch.  Use previous procedures to 

drive forward. 

3.)  As the Terminator® is removing flooring material have another person at the side of the machine remove 

all debris.  

Содержание Teerminator-2000



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды