manualshive.com logo in svg

Innovatech Teerminator-2000, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Innovatech Teerminator-2000 Скачать руководство пользователя страница 16

INNOVATECH PRODUCTS & EQUIPMENT CO., INC. 

16

 

Ignition and Fan Switches 

 

1.

3. 

4. 

 

2. 

7. 

6. 

5. 

Figure 4: Control Console 

 

1.)  The IGNITION SWITCH (selector ON/OFF/START) is located in the upper right hand corner of the 

gauges panel.  To START the engine, turn the key switch ON (key switch is on some models).  Pause for 
one or two seconds, turn to START and hold until the engine fires, then release the switch.  

ALWAYS 

turn this switch OFF when the Terminator® is not in use. 

 

2.)  The HEADLIGHT SWITCH (ON/OFF toggle) is located on the system gauges panel.  

Do not leave the 

fan switch ON when the machine is not in use. 

 

System Gauges 

 

The system gauges monitor the Terminator®’s various operating systems. These gauges are located on the 

system gauges panel and consist of the following:  
 

3.)  AMP/ALTERNATOR:  shows battery activity. 

 

4.)  HOUR METER:  shows the exact running time of the machine.  The hour meter will continue to run 

while the key and lever ignition switch are on.  

 

 

5.)  HYDRAULIC OIL TEMPERATURE (a.k.a. hydraulic fluid):  Normal temperatures are below 120°F.  

Hydraulic fluid temperature exceeding 200°F may damage the hydraulic system and in turn, damage the 
Terminator®. 

 

6.)  OIL PRESSURE GAUGE:  shows the oil pressure of the engine lubricant.  During normal operation, this 

gauge should register in the safe range shown on the dial (40-60 PSI).  If this pressure drops suddenly, 
shut the engine OFF immediately and check the oil supply.  NEVER attempt to operate the Terminator® 
without adequate oil because you will destroy the engine and its parts.  If water or oil temperatures exceed 
maximum temperature, lift lid and remove side panels.  Let run for five minutes.  Turn machine off to 
cool for 30-60 minutes.  If possible, let cool by an open outside door or window.  Never remove radiator 
cap if water is boiling out.  Always, let the machine cool down. 

 

7.)  WATER TEMPERATURE GAUGE:  normal range is 190°F-230°F.  

 

 When the machine is new, this 

gauge may register 220°F-250°F for the first 50± hours of operation.  This is the normal break-in period.  
After this break-in period, the gauge shows the actual temperature of the water.  

 

Blade Assembly 

Содержание Teerminator-2000



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды