manualshive.com logo in svg

Innovatech Teerminator-2000, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Innovatech Teerminator-2000 Скачать руководство пользователя страница 14

INNOVATECH PRODUCTS & EQUIPMENT CO., INC. 

14

 

COMPONENTS AND OPERATING SYSTEMS 

 

The major components and the operating systems of the Terminator® are discussed in detail below.  

 

Engine and Fan 

 

Figure 2: Engine and Fan 

 

  The propane-powered engine and fan are located under the hood.  The engine provides the power to drive 
the Terminator®.  
 
  The fan ventilates and cools the entire engine and fuel tank area on the older models.  A safety guard covers 
the fan. 

NEVER operate the machine unless the guard is in place.  If you remove the guard to clean the 

fan, replace the guard before you start the engine again.  ALWAYS keep your hands away from the fan 
when the engine is running.

 

   

  The engine requires regular inspection and service, to maintain its efficiency and prolong its operating life.  
Check the oil level and clarity daily.  Change the oil every 60 hours of running.  

Do not allow the oil to get 

muddy before changing it because dirty oil can damage the engine and its parts

 (see the Maintenance 

section for details).  If operating machine in very dusty areas, change oil every 40 hours.   
 
  Air filter should be checked every day if machine is run 4 or more hours, to make sure it is clean.  Blow 
dust out or replace with another filter. 

 

Содержание Teerminator-2000



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды