innovair BIN1036C2V02 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 47

background image

25

8. Electronic function

8.1 Abbreviation

T1: Indoor room temperature

T2: Coil temperature of evaporator

T3: Coil temperature of condenser

T4: Outdoor ambient temperature

T5: Compressor discharge temperature

8.2 Display function

8.2.1 Icon explanation on indoor display board.

①

Auto indicator

This indicator illuminates when the air conditioner is in AUTO operation.

②

Timer indicator

This indicator illuminates when TIMER is set ON/OFF.

③

PRE.-DEF. Indicator

This indicator illuminates when the air conditioner starts defrosting automatically or when the warm air

control feature is activated in heating mode.

④

TEMPERATURE indicator

Usually it displays the temperature settings. When change the setting temperature, this indicator

begins to flash, and stops 20 seconds later. It displays the room temperature when the air conditioner

is in FAN only operation, and the range of that is 0~50

℃

. When the unit stops operation, it returns to

original factory settings. It will also display the codes when malfunction or protection happen.

⑤

Frequency indicator

This indicator appears only when the compressor is in operation and indicates the current operating

«
...
25
26
27
28
29
...
»

Содержание BIN1036C2V02
















































Отзывы:

Нет отзывов

Похожие инструкции для BIN1036C2V02

R32 Split Series

Бренд: Daikin Страницы: 28

Бренд: Jafanda Страницы: 6

Бренд: Qlima Страницы: 50

Бренд: RS Страницы: 12

DOLCECLIMA AIR PRO 14AC

Бренд: Olimpia splendid Страницы: 92

Бренд: Godrej Страницы: 50

Бренд: Daikin Страницы: 16

Бренд: OcaRina Страницы: 14

Бренд: Olmo Страницы: 19

Бренд: easymaxx Страницы: 42

Бренд: ActivePure Страницы: 2

Therapure TP250

Бренд: Boneco Страницы: 32

Бренд: airo COMFORT Страницы: 8

Бренд: Sonnenkonig Страницы: 64

Бренд: Daikin Страницы: 39

Бренд: Convair Страницы: 16

Бренд: Admiral Страницы: 38

Бренд: AC Pro Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды