Innotech Omni C14 Скачать руководство пользователя страница 30

Страница: 30 / 90

Omni Installation Instructions

Page 30

Edition 1.2 dated 03.08.2018

2-5 HMI Installation

2-5.1 OMH01 Retrofit Onboard HMI

The OMH01 retrofit HMI display can only be installed by Innotech technical personnel. Refer to the

OMH01 Installation Instructions supplied with the HMI for the correct installation procedure.

2-5.2 OMH02 External USB HMI Display Module

The external HMI can be mounted in the cabinet near the Omni controller(s) or used handheld. A USB

cable is plugged into the back of the HMI and into the USB-A socket of the Omni C20 or Omni C40

controller.

One HMI can be used with multiple controllers by plugging the USB cable into another controller. The

USB cable can be plugged in while the controller is powered.

Figure 2-22:

Omni USB HMI Display

Содержание Omni C14



























































































Результаты поиска

Содержание Omni C14

Отзывы:

Похожие инструкции для Omni C14

Бренды по названию

Популярные бренды

Innotech Omni C14, Руководство по установке

Результаты поиска

Содержание Omni C14

Отзывы:

Похожие инструкции для Omni C14

Бренды по названию

Популярные бренды