Turn ON the small pin switch in bottom of iTaste MVP,
connect cable into USB OUTPUT port(DC 5V ,
maximum output current 0.5A ,the 3 most popular
power connectors for iPhone/iPods, MiniUSB
(Motorola/Blackberry), a Micro USB (Motorola/Nokia
/LG/Samsung). Turn OFF the small pin switch when
finish charged your electronics .
button will activate the battery.
Press the “U“ button for 3 seconds to enter variable
voltage mode. The screen will show you the Puff
counter first followed by the last adjustment (The last
adjustment may be a voltage or wattage setting), after
showing the last adjustment, the iTaste MVP will enter
variable voltage mode. Voltage can be adjusted from
3.3 to 5.0 volts in .1 volt increments by pressing the
“U” button.
Press the “P“ button for 3 seconds to enter variable
wattage mode. The screen will show you the Puff
counter first followed by the last adjustment (The
last adjustment may be a voltage or wattage setting),
after showing the last adjustment, the iTaste MVP
will enter variable wattage mode. Wattage can be
adjusted from 6.0 to 11 watts in .5 watt increments
by pressing the “P” button.
Hold both the “P” and “U“ buttons simultaneously for
2 seconds. The screen will show a series of readings,
the first being the resistance of the attached load (
Rx.x , for example R2.2), the second being the battery
voltage, the third being the number of puffs since the
device was last turned off and the fourth being the
last set voltage or wattage. If no load is attached the
display with show “NON”.
There are three main buttons on the iTaste MVP: “ ”
button, "P" button and "U" button; all the functions
can be activated by using those three buttons to
change settings in a single step, without the use of a
menu system. Your chosen mode will be displayed on
the digital screen.
Quickly clicking the “ ” button three times will enable
or disable the battery. Once enabled, holding down the
Portable power source for electronic products
OPERATION GUIDE
ON/Off:
Variable Voltage Mode :
Variable Wattage Mode :
Ohms Meter & Battery Level Indicator & Puff Counter:
7
6
5
4
3
2
1
1
2
5
6
7
3
4
NO.
Function description
iClear dual coil clearomizer
ON/OFF Power button:
The iTaste MVP battery capacity is displayed via green,
yellow and red LED lights. Green = Fully Charged
Yellow = Half Discharged Red = In need of charging
“P” button: VW
“U” button: VV
Portable power source for electronic products
Turn ON this small pin switch when use as power source
for electronic products .
Recharge iTaste MVP with a standard USB Micro cable plug,
it can also work as a passthrough for use while charging.
If you wish to check the number of puffs taken since
the iTaste MVP was last turned off, you can also hold
either the “P” or the “U“ button to display the Puff
Counter which will be followed by the display of
current mode (VV mode or VW mode). In this state,
you can also adjust the voltage or wattage by pressing
the “P” or “U“ button.
Replace or refill the cartridge if vapor volume decreas
-
es.
The manufacturer is not responsible for a damaged
atomizer, cartomizer or clearomizer.
Driving them with too much power for too long or
running them dry can burn them out.
We recommend you start with a low voltage setting
and work your way up until when you find the right
setting for your atomizers, cartomizers or clearomiz
-
ers.
Never use your iTaste MVP without an atomizer,
cartomizer or clearomizer. Connecting to a volt meter
without the load required for high voltages can
damage the device.
When plug in, the LED light will blink from red to
yellow to green , then stay on current battery capacity
level , for example , if your battery current capacity
yellow , then LED light will stay on Yellow , then
change to Green.After the iTaste MVP is fully
recharged, the LED lights will turn off.
Recharge iTaste MVP with a standard USB Micro cable
plug, it can also work as a passthrough for use while
charging.
Plug the USB cable into iTaste MVP ’s input and plug
the other end into a power source.
The color of the LED light indicates the remaining
battery life. After the iTaste MVP is fully recharged,
the LED lights will turn off.
1.Red LED light = battery voltage is lower than 3.61V
2.Yellow LED light = battery voltage between 3.61V
and 3.75V
3.Green LED light = battery voltage is more than 3.75 V
4.Red LED will keep blinking for 8 seconds when battery
capacity is lower than 3.3V and the device will turn off
automatically.
5.Red LED light will stay on for 5 seconds when a load
short circuit is detected or the current of the coil is
more than 3.5A, then no vapor will be produced.
6.If you take a drag for longer 10 seconds, the battery
will stop it’s output, the RED light will blink 10 times,
and the iTaste MVP won’t continue to work until you
press the power button again.
The LED light will blink in different colors to indicate
the current battery voltage
LED Light Blinking Mode:
Notes:
CHARGING ITASTE MVP
