in71TS3N2D Series
Indoor Outdoor Bullet Camera
Quick Start Guide
Before operating this product, please read this quick-start guide to ensure proper use.
Please store these instructions a safe place for future reference.
FeaTureS
• IP66 Die Cast Aluminium Housing
• Varifocal lens
• High Resolution 800TVL
• 0 Lux IR on, 0.01 Lux
• Wide Dynamic Range
• Wire Management Mount
• Sun Shield
• HLC, BLC, DEFOG
• Sens Up
• On Screen Menu
• 3 Axis gimbal
• 12VDC/24VAC Powered
preCauTIONS
1. Before installing and operating the unit, please read this manual carefully.
2. Precision components are contained in this camera, please avoid violent vibrations during
installation and maintenance. Do not connect the power until you have completed the
installation.
3. Please obey all local electrical wiring regulations when using this unit.
4. Do not use abrasive or corrosive materials for cleaning. Use only a soft cloth for cleaning.
5. To prevent damage to the lens or sensor, do not point the camera directly into the sun
or very strong light sources.
6. Do not use the camera outside it’s working temperature (-10°C~ 50°C / 14°F ~122°F) or
humidity (<90%) ranges.
7. Ensure that the power supply meets the current requirements of the camera and that
the supply voltage is inside the tolerances of the camera: 12vdc or 24VAC ±10%
8. Ensure that the fixings used are adequate to support the load of camera.
9. In case of camera failure, do not attempt to dismantle or service the camera yourself.
Please refer to qualified service personnel for repair of the camera.
CONNeCTIONS
1. Analog Video BNC Connector.
2. Power Input connector. This is a 2 pin non-removable terminal screw connector.
Observe polarity of 12VDC connections. 24VAC power is not polarity sensitive.
Refer to the diagrams below for clarification.
3. Sun Shield
4. Thumb screw to attached Sun Shield
5. Service Port for Analog Video
6. Focus Screw (Far:Near)
7. Zoom Screw(Wide:Telephoto)
8. Service Cable
+ (Pos)
- (Neg)
MOuNTING
1. Mark and drill the three mounting holes for the base. Choose an appropriate drill bit for the
surface you are drilling in to and ensure that the diameter is correct for the fixings being
used. Mark and cut/drill a central 20mm (¾”) diameter hole for the cable and connectors.
2. Use appropriate screws and wall plugs for the mounting surface in use.
3. Ensure that the fixings can adequately bear the weight of the camera.
4. Make the video and power connections and commission the camera.
LeNS aND pOSITIONING
The bullet camera has an integral varifocal lens, a OSD button and Service port (adjusted from
the access port on bottom of camera) along with a 3-axis mount which can be manipulated to
position the camera.
To position the camera to give the required image content, gently loosen the two hex screws
located on the main mount to adjust the tilt. To adjust the camera azimuth loosen the hex nut
on base of bullet or back of camera, gently turn to reach desired position then retighten.
When the OSD menu is launched, you are
presented with the adjacent opening screen.
A menu option followed by a
indicates the
presence of a sub-menu. Options set to OFF will
not show a
until set to ON
Use RETURN
to return to the previous menu.
FOCuS aDJuST
menu:
• From the Main Menu, turn the Focus ADJ from OFF to ON to create a Focus Adjust
Box on the screen’s bottom left
• Move the lens to direct towards the object to be focused, and turn the lens focus
from near to far until the location from the Focus Assist Box shows a green bar.
Next turn the lens focus until the yellow bar has a similar size with the green bar
for focus. Your camera should now have a clear crisp image.
LeNS menu:
•
MODe
- ALC (Auto Iris) or ELC (Manual)
selection
•
INDOOr -
Default, set to fixed values
•
OuTDOOr-
Iris and shutter will auto
adjust to lighting situation.
eXpOSure
menu:
•
BrIGHTNeSS -
Sets the level of the overall brightness
•
SHuTTer
- Auto, Manual, FLK selection,
1/50~1/60K. Set this on to reduce the
exposure time of each image. This can be
used to reduce blur in images with fast
changing content. FLK mode Use this when
flicker is observed in the image under
fluorescent lighting.
•
SeNS up -
Slows frame rate and increases
low light sensitivity
•
aGC- Level Control -
Used to adjust overall
gain
Rev 0.1
MAIN MENU
FOCUS ADJUST
LENS
ELC
EXPOSURE.
BACKLIGHT
WDR
DAY&NIGHT
WHITE BAL
AUTO
IMAGE
DNR
MIDDLE
SPECIAL
SYSTEM
EXIT
EXPOSURE
BRIGHTNESS 10
SHUTTER
AUTO
SENS-UP
X2
AGC
16
RETURN
RET
FOCuS aDJuST MeNu
eXpOSure MeNu
OSD MaIN MeNu
LeNS MeNu
LENS
MODE
INDOOR
RETURN
RET
To set lens to correct field of view and focus remove the access plug on the bottom of the
camera. See image below. First plug your service cable into the service port ⑤ then into
your monitor. The field of view may then be adjusted by turning the zoom lever, ⑦, and
moving until the required field of view is obtained. Next turn the focus lever ⑥ and adjust
to obtain optimum focus. When complete screw the access port onto camera to maintian
water seal.
