Ingics iGS03E Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 21

Ingics iGS03E Скачать руководство пользователя страница 10

INGICS

TECHNOLOGY

Web User Interface

You can review current configuration or modify it on the web UI. There are various function

groups listed on the top of UI.

Any change in the page needs to be saved first before switching to another page, otherwise the

modification will be lost. And after all changes made, click reboot to make the changes effective.

System

Display firmware and device information, including MAC address and IP address in station mode

are shown here.

Wi-Fi

Users can configure iGS03M’s WiFi device as an WiFi AP or join to the other AP. The related

settings can be managed on this page.

AP Mode

SSID: The default name is IGS03 plus

the last digits of the mac address.

Security: Open, WPA-PSK, WPA2-PSK

and WPA-PSK/WPA2-PSK are

supported. WPA2-PSK is

recommended.

Password: 8-63 characters can be

input

Channel: 1~11(ch12 and ch13 could be supported by request)

Station Mode

This mode is used for transferring

data by *WiFi.

Scan: Click it to scan available APs.

INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM

10

«
...
8
9
10
11
12
...
»

Содержание iGS03E






















Отзывы:

Нет отзывов