background image

EN-41   

80446339

 Rev B

EN

The following settings are displayed in this section:

Table 27: Backlight Settings

Display Text

Description

Backlight 
Brightness

Adjusts the brightness of the display.

Enable Backlight 
Auto-Off

Enables the controller to shut-off the backlight if 
there is no user activity for the delay time shown.

Backlight Auto-Off 
Delay Time

Determines how many seconds of inactivity it will 
take before the controller will shut-off the backlight.

NOTICE

The backlight will be switched on whenever any of the controller’s 

keys are pressed . 

The START, STOP, LOAD, UNLOAD, RESET, and ACKNOWLEDGE keys on 

the controller remain functional while the backlight is switched off . It 

is recommended to press the ENTER key or one of the navigation keys 

in order to switch the backlight on .  

Pages 7-8:  Ethernet Settings

Figure 75: Ethernet Settings

The following settings are displayed in this section:

Table 28: Ethernet Settings

Display Text

Description

Enable Ethernet

Allow connection by users to utilize the network 
enabled functionality of the controller.

Enable DHCP

Allow the controller to automatically receive an IP 
address from the Local Area Network (LAN).

IP Address Setting

When DHCP is not enabled, this setpoint sets the 
IP address of the controller.

IP Address Actual

This will match the IP address setting when DHCP 
is not enabled.  If DHCP is enabled this will display 
the address assigned to the controller by the 
DHCP server.

MAC Address

This is the unique hardware MAC address for the 
controller.  This can not be changed.

Subnet Mask Setting

Setpoint for the subnet mask.

Subnet Mask Actual

Current reading/setting for the subnet mask.

Default Gateway 
Setting

Setpoint for the default gateway.

Default Gateway 
Actual

Current reading/setting for the default gateway.

Accept

After editing the desired setpoint navigate to the 
accept setting and press enter in order for the 
values in the setting variables to be confirmed by 
the controller.

Cancel

Discard any changes made to the Ethernet 
settings.

 Status folder

NOTICE

All information on these pages is read only .

Pages 1 -2: Analog Inputs

Figure 76: Analog Inputs

The following inputs are displayed in this section:

Package Discharge Pressure
Sump Pressure
Airend Discharge Temperature
Injected Coolant Temperature
Aftercooler Discharge Temperature
Separator Pressure Drop
Coolant Filter Pressure Drop
Inlet Vacuum
Aftercooler Discharge Pressure (integrated dryer compressors only)
Remote Pressure (optional)
Coolant Filter Inlet Pressure
Coolant Filter Outlet Pressure
Interstage Pressure (2-stage compressors only)
Evaporator 
Condenser















 110812.16.23

Содержание R132

















































Отзывы: