Table 2: Specifications
Models
Operating
Mode
Air System
Rated Performance (at rated pressure/volume)
Net Weight **
Rated
Operating
Pressure
Air Consumption
(at rated pressure
and load)
Full Drum
Line Pull
Full Drum
Line Speed
Max Stall Pull, 1st
Layer
Force
Limit
Factor
Maximum
Freeboard
scfm
cu.m/
min
lbs
kgs
fpm
m/min
lbs
kgs
inch
mm
lbs
kgs
FA2.5i-
MR
Utility
90 psig (630
kPa/6.3 bar)
700
20
5,000
2,273
132
40
10,500
4,763
N/A
0.5
13
1,190
540
Man Rider
3,180
1,445
173
53
1.3
32
1,265
574
FA2.5i-
MR-CE
Utility
70 psig (480
kPa/4.8 bar)
5,000
2,273
98
30
1.6
1,115
506
Man Rider
3,180
1,445
135
41
6,300
2,858
N/A
1,290
585
FA5i-
MR
Utility
90 psig (630
kPa/6.3 bar)
11,000
5,000
54
16
29,000
13,154
0.5
13
1,895
860
Man Rider
6,875
3,124
75
23
1.5
38
2,000
907
FA5i-
MR-CE
Utility
80 psig (550
kPa/5.5 bar)
11,000
5,000
52
16
25,900
11,748
1.6
1.6
40
1,985
900
Man Rider
6,875
3,124
72
22
15,200
6,895
N/A
2,025
919
** Weight of standard winch without wire rope.
Table 3: Specifications
Models
Air Motor Pipe
Inlet Size
Minimum Air System
Hose Size (inside
diameter)
Drum
Barrel
Diameter
Drum
Flange Diameter
Recommended Wire
Rope Size
Sound
Pressure
Level
Sound
Power
Level
Maximum
Foundation Anchor
Shear Force at One
Capscrew
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
dBA
dBA
lbs
N
FA2.5i-
MR &
FA2.5i-
MR-CE
1.25
32
1.50
38
10.75
273
19
483
5/8
16
97
109
2,210
9,830
FA5i-MR
& FA5i-
MR-CE
1.25
32
1.50
38
15
381
27
686
3/4
20
97
109
4,850
21,570
Sound measurements have been made in accordance with ISO 11201, ISO 3744-3746
and ISO 4871 test specifications for sound from pneumatic equipment. Readings
shown are based on the average noise level of each winch configuration,
proportionate to the utilized time in a regular cycle.
Lpc (Peak Sound Pressure) does not exceed 130 dB. Performance based on 90 psig
(6.3 bar/630 kPa) operating pressure.
Table 4: Available Drum Lengths
Models
Drum Lengths
in
mm
in
mm
in
mm
in
mm
in
mm
in
mm
in
mm
in
mm
in
mm
in
mm
FA2.5i-
MR/
FA2.5i-
MR-CE
8
203
12
305
16
406
20
508
24*
610*
30
762
36
915
40** 1016**
42**
1067** 50**
1270**
FA5i-MR/
FA5i-MR-
CE
---
---
* Standard Length
** Special, contact factory
Refer to sales literature for winch drum wire rope storage capacities.
NOTICE
•
All -E winch models are manufactured to previous European Machinery
directives. Refer to Data (Name) Plate on winch to determine model. If winch
is a custom build also refer to the Declaration of Conformity for serial
number break.
n
Traceability
Load bearing parts are documented to provide traceability. Documentation includes
chemical and physical properties of raw material, heat treating, hardening, tensile
and charpy tests as required for the part.
Units with M1, M2 or M3 in the model code have traceable load bearing
components.
M1 – Material Traceability certificates according to EN 10204 (Ex DIN 50049) 2.2 on
load bearing parts. Conformity documents affirm (by the manufacturer) that parts
are in compliance with requirements of the order, based on non-specific inspection
and testing (i.e. results are typical material properties for these parts).
M2 – Material Traceability certificates according to EN 10204 (Ex DIN 50049) 3.1b on
load bearing parts. Conformity documents affirm (by a department independent of
the manufacturing department) that actual parts are in compliance with
requirements of the order, based on specific inspection and testing (i.e. results are
actual material properties for these parts).
M3 – Material Traceability certificates according to EN 10204 (Ex DIN 50049) 3.1b on
load bearing parts. Conformity documents affirm (by a department independent of
the manufacturing department) that the actual parts used in the product are in
compliance with the order, based on specific inspection and testing (i.e. results are
actual material properties for these parts in a finished, as delivered condition).
Components with part numbers ending in CH are charpy parts for use under extreme
cold conditions. Traceability requirements must be stated when reordering these
parts for continued certification.
n
ATEX
Refer to labeling on product, located near or on data (name) plate, for specific ATEX
designation. Product not marked as such, are not suitable for use in any potentially
explosive atmosphere (ATEX). Refer to Product Safety and Maintenance Information
Manuals for further explanation.
II 2 GD c IIB 200°C X
(Dwg. MHP2584)
4
Form MHD56435 Edition 6
Содержание FA2.5-MR-CE
Страница 16: ...R www ingersollrandproducts com...
