manualshive.com logo in svg

Ingersoll-Rand DOOSAN HP375WCU, Руководство по эксплуатации и техническому обслуживанию, Страница: 53 / 73

Поделиться
Скачать
Ingersoll-Rand DOOSAN HP375WCU Скачать руководство пользователя страница 53

Maintenance

Operation & Maintenance Manual

22592086

53

Initial 

500 miles 

/850 km

Daily

Weekly

Monthly

3 Months 

500 hrs.

6 Months 

1000 hrs

12 

Months

2000 hrs

18 

Months

3000 hrs

*Fue/Water Separator Element

R

Compressor Oil Filter Element

R

Compressor Oil

R

Engine Oil Change

R

Engine Oil Filter

R

*Water Pump Grease.

R

*Wheels (Bearings, Seals, etc.)

C

G

*Engine Coolant

C

R

Fuel Filter Element

R

*Injection Nozzle Check

C

Shutdown Switch Settings

T

Scavenger Orifice & Related Parts

C

Oil Separator Element

R

*Feed Pump Strainer Cleaning.

C

*Valve Clearance Check

C

Lights (running, brake, & turn)

CBT

Pintle Eye Bolts

CBT

* Brakes

C

C

* Brake linkage

C

* Emergency stop

T

Running gear linkage

G

Safety valve

C

Running gear bolts(1)

C

*Disregard if not appropriate for this particular machine.

D

 = Drain

(1) or 3000 miles/5000km whichever is the sooner

G

 = Grease

(2) or as defined by local or national legislation

R

 = Replace

C

 = Check (adjust, clean or replace as necessary)

T

 = Test

CBT

 = Check before towing.

W I

 = or when indicated if earlier.

CR

 = Check and report

Refer to specific sections of the operator's manual for 
more information.

Содержание DOOSAN HP375WCU










































































Отзывы:

Нет отзывов