Infranor Xtracontrol DC2 Скачать руководство пользователя

Страница: 27 / 87

User Manual V1.3 | XtracontrolDC2, XtracontrolET2, XtracontrolEC21

Connection

WARNING

Uncontrolled and unpredictable operational behaviour!

Failure in certain components in electronic control systems may result in

uncontrolled and unpredictable operational behaviour.

▶

All types of failure and the associated fuse systems are to be taken

into account at system level.

▶

Comply with all automation system manufacturer instructions.

5.1

Power supply

The device is powered by an external 24 V DC power supply. It is not designed to be connected to a DC mains
supply.

▶

Before plugging in the device, ensure that the external power supply meets the required specifications (type K

to 61131-2).

External power supply (24 V DC)

Supply voltage

+24 V DC SELV (–15% / +20%)

Alternating current proportion

Max. 5%

The direct voltage level must not fall below 20.4 V.

Power consumption

Total max. 3.2 A at +24 V DC (1.2 A electronics; 2 A external I/O)

Energy buffering

10 ms

Internal power supply

A power supply for the system electronics for an input voltage of 24 V DC (–15% / +20%) is integrated into the
device. The power supply has integrated protection against reverse polarity and surge current protection (1.2 A).

Installation

▶

All connections and cables must be laid out so as to prevent inductive and capacitive interference causing any

damage to the device.

▶

Ensure that the infeed lines provide adequate current and voltage carrying capacity.

Содержание Xtracontrol DC2
























































































Результаты поиска

Содержание Xtracontrol DC2

Отзывы:

Похожие инструкции для Xtracontrol DC2

Бренды по названию

Популярные бренды

Infranor Xtracontrol DC2, Руководство пользователя

Результаты поиска

Содержание Xtracontrol DC2

Отзывы:

Похожие инструкции для Xtracontrol DC2

Бренды по названию

Популярные бренды