background image

July 14, 2013 

INFODRAW                                        MRS-400 User Manual v5.4.1                                                                        

 

 

 

98 

 

4-1-9   GPIO (Sensors and Switches): 

The MRS-400 unit has 4 input and 4 output ports. The GPIO ports are at 

TTL

 level. The GPIO 

connections are built in to the MRS-400 unit. The ports are reachable through the 

GPIO 

plugs on the side of the device. 

The GPIO ports can be set up to trigger a variety of alarms including live video streaming, 
video/audio recording, GPS tracking etc. These features are set on the MRS monitor. The 
unit can also send a SMS to any number of phones as a result of a GPIO trigger (refer to the 

SMS Alerts from Device

 section of this user manual).   

The GPIO trigger actions are set in the 

“Alarm Settings”

 window of the MRS Monitor. Follow 

these instructions: 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Double click on the 

“Contacts 

Alarm”

 item on the left hand 

side of the screen under 

“My 

Monitor”

The 

“Alarm Settings” 

window 

will open. Select the desired 
actions that the GPIO ports will 
trigger when activated. Then 
click 

“OK”

The descriptions of these 
trigger actions are listed below: 

Содержание MRS-400



































































































































































































Отзывы: