INFODRAW MRS-400 Скачать руководство пользователя страница 71

Страница: 71 / 194

July 14, 2013

INFODRAW MRS-400 User Manual v5.4.1

4-1-6-2 Audio Streaming:

Audio In:

Double clicking on the

“Audio In 1”

channel

opens the audio stream of just the Microphone
on the MRS-400 device to the speakers on the
PC. Double clicking again on the

“Audio In 1”

channel stops the audio stream.

The MRS-400 unit has a built-in microphone.

An external microphone can also be attached
to the

“Audio Input”

on the “Audio in/out

splitter cable”, included with the MRS-400 unit.

Ensure that you have a speakers connected to
the PC.

Audio Out:

Double clicking on the

“Audio Out 1”

channel

opens the audio stream from the PC microphone
to the embedded MRS-400 speaker or to the
headphones connected to the line out port.

Double clicking on the

“Audio In 1”

channel stops

the audio stream.

Ensure that you have speakers and a microphone
connected to your PC.

Start Audio Stream

Stop Audio Stream

Содержание MRS-400



































































































































































































Результаты поиска

Содержание MRS-400

Отзывы:

Похожие инструкции для MRS-400

Бренды по названию

Популярные бренды

INFODRAW MRS-400, Руководство пользователя

Результаты поиска

Содержание MRS-400

Отзывы:

Похожие инструкции для MRS-400

Бренды по названию

Популярные бренды