Infinium OMNI Express Скачать руководство пользователя страница 75

Страница: 75 / 117

Use

r’s

Manual of OMNI Express Patient Monitor

- 67

037.007.0001 Rev.2

SAFETY

CLASSIFICATION

◆

According to the degree of safety of application in the presence of FLAMMABLE

ANAESTHETIC MIXTURE WITH AIR, OR WITH OXYGEN OR NITROUS OXIDE:
The ISA is not suitable for use in the presence of FLAMMABLE ANAESTHETIC
MIXTURE WITH AIR, OR WITH OXYGEN OR NITROUS OXIDE.

◆

According to the degree of protection against harmful ingress of water: IPX4

◆

According to sterility: The ISA system contains no sterile parts.

◆

According to the model of operation: CONTINUOUS OPERATION

◆

According to the degree of protection against electric shock:

Nomoline Family sample lines are classified as DEFIBRILLATION PROOF TYPE BF
APPLIED PART

◆

The combination of OMNI Express and ISA shall be considered a ME SYSTEM.

WARNINGS

◆

The ISA sidestream gas analyzer is intended for use by authorized and trained

medical personnel only.

◆

Use only Nomoline sampling lines manufactured by PHASEIN.

◆

The ISA sidestream gas analyzer must not be used with flammable anesthetic

agents.

◆

Carefully route the sampling line to reduce the risk of patient entanglement or

strangulation.

◆

DO NOT re-use disposable sampling lines.

◆

DO NOT lift the ISA/OMNI Express by the sampling line as it could disconnect from

the ISA/ OMNI Express >, causing the ISA/ OMNI Express to fall on the patient.

◆

Used disposable sampling lines shall be disposed of in accordance with local

regulations for medical waste.

◆

DO NOT use adult/pediatric type sampling line configurations with infants, as this

may add dead space to the patient circuit.

◆

DO NOT use infant type sampling line configurations with adults, as this may cause

excessive flow resistance.

◆

DO NOT use the ISA sidestream gas analyzer with metered-dose inhalers or

nebulized medications as this may clog the bacteria filter.

◆

Check that the gas sample flow is not too high for the present patient category.

◆

Since a successful zeroing requires the presence of ambient air (21% O

and 0%

) in the gas analyzer, ensure that the ISA is placed in a well ventilated place.

Avoid breathing near the ISA sidestream gas analyzer before or during the zeroing
procedure.

◆

The Nomoline sampling line and its interfaces are non-sterile devices. To avoid

damage, do not autoclave any part of the sampling line.

◆

Never sterilize or immerse the ISA sidestream gas analyzer in liquid.

◆

Measurements can be affected by mobile and RF communications equipment. Make

sure that the ISA sidestream gas analyzer is used in the electromagnetic environment
specified in this manual.

◆

ISA sidestream gas analyzer is intended only as an adjunct in patient assessment. It

must be used in conjunction with other assessments of clinical signs and symptoms.

◆

Replace the sampling line if the sampling line input connector starts flashing red, or a

Nomoline occlusion message is displayed on the OMNI Express.

◆

No modification of this equipment is allowed without authorization of the manufacturer.

If this equipment is modified, appropriate inspection and testing must be conducted to
ensure continued safe operation.

◆

ISA sidestream gas analyzers are not designed for MRI environments.

◆

During MRI scanning, the OMNI Express must be placed outside the MRI suite.

◆

Use of high frequency electrosurgical equipment in the vicinity of the ISA/OMNI

Express may produce interference and cause incorrect measurements.

◆

DO NOT use external ambient cooling of the ISA device.

Содержание OMNI Express






















































































































Результаты поиска

Содержание OMNI Express

Отзывы:

Бренды по названию

Популярные бренды

Infinium OMNI Express, Руководство пользователя

Результаты поиска

Содержание OMNI Express

Отзывы:

Бренды по названию

Популярные бренды