Infineon TRAVEO T2G family CYT4D Series Скачать руководство пользователя

Страница: 66 / 80

Application Note

66 of 80

002-26071 Rev. *B

2021-09-07

Clock configuration setup in TRAVEO™ T2G family CYT4D series MCUs

Supplementary information

Table 27

Clock input to SAR ADC

Peripheral function

Operation clock

Unit clock

SAR ADC

CLK_GR9 (Group 9)

Unit0: PCLK (PCLK_PASS_CLOCK_SAR0)

Table 28

Clock input to CXPI

Peripheral function

Operation clock

Channel clock

CXPI

CLK_GR5 (Group 5)

PCLK (PCLK_CXPI0_CLOCK_CH_EN0)
PCLK (PCLK_CXPI0_CLOCK_CH_EN1)

Table 29

Clock input to SMIF

Peripheral function

“clk_slow”

domain

(XIP AHB-Lite

Interface0)

“clk_mem”

Domain

(XIP AHB interface)

“clk_sys”

domain

(MMIO AHB-Lite

interface)

“clk_if”

domain

SMIF

clk_slow

clk_mem

CLK_GR4

CLK_HF6

Table 30

Clock input to AUDIOSS

Peripheral function

clk_sys_i2s

clk_audio_i2s

AUDIOSS

CLK_HF5

CLK_GR8

Note:

For details on Ethernet clocks, see the

architecture TRM

6.2

Use case of the clock calibration counter function

The clock calibration counter has two counters that can be used to compare the frequency of two clock
sources. All clock sources are available as a source for these two clocks. For details, see the

architecture TRM

Use the following procedure to calibrate using the clock calibration counter:

Calibration Counter1 counts clock pulses from Calibration Clock1 (the high-accuracy clock used as the
reference clock). It counts downwards.

Calibration Counter2 counts clock pulses from Calibration Clock2 (measurement clock). It counts upwards.

When Calibration Counter1 reaches 0, Calibration Counter2 stops counting upwards, and its value can be
read.

The frequency of Calibration Counter2 can be obtained by using its value and the following equation:

CalibrationClock2

Counter2value
Counter1value

× CalibrationClock1

Figure 23

shows an example of the clock calibration counter function when ILO0 and ECO are used. ILO0 and

ECO must be enabled. See ILO0 and ECO for

3.4

Configuring ILO0/ILO1

and

3.1

Setting the ECO

Содержание TRAVEO T2G family CYT4D Series

















































































Результаты поиска

Содержание TRAVEO T2G family CYT4D Series

Отзывы:

Похожие инструкции для TRAVEO T2G family CYT4D Series

Бренды по названию

Популярные бренды

Infineon TRAVEO T2G family CYT4D Series, Руководство пользователя

Результаты поиска

Содержание TRAVEO T2G family CYT4D Series

Отзывы:

Похожие инструкции для TRAVEO T2G family CYT4D Series

Бренды по названию

Популярные бренды