Infineon TRAVEO T2G family CYT4D Series Скачать руководство пользователя

Страница: 26 / 80

Application Note

26 of 80

002-26071 Rev. *B

2021-09-07

Clock configuration setup in TRAVEO™ T2G family CYT4D series MCUs

Configuration of the FLL and PLL

This section describes the configuring of the FLL and PLL in the clock system.

4.1

Setting FLL

4.1.1

Operation overview

The FLL must be set before using it. The FLL has a current-controlled oscillator (CCO); the output frequency of
this CCO is controlled by adjusting the trim of the CCO.

Figure 12

shows the steps to configure the FLL.

Start

End(Success)

Yes

Wait until CCO is available?

Wait until FLL is locked?

FLL configuration

Enable CCO

Enable FLL

Based on the specification of the application,

configure FLL to each register.

FLL already enabled?

Yes

End(No Change)

TIMEOUT?

Yes

FLL disabled

End(Timeout)

TIMEOUT?

Yes

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

Figure 12

Procedure for setting the FLL

For details of FLL and FLL setting registers, see the

architecture TRM

and

registers TRM

Содержание TRAVEO T2G family CYT4D Series

















































































Результаты поиска

Содержание TRAVEO T2G family CYT4D Series

Отзывы:

Похожие инструкции для TRAVEO T2G family CYT4D Series

Бренды по названию

Популярные бренды

Infineon TRAVEO T2G family CYT4D Series, Руководство пользователя

Результаты поиска

Содержание TRAVEO T2G family CYT4D Series

Отзывы:

Похожие инструкции для TRAVEO T2G family CYT4D Series

Бренды по названию

Популярные бренды