Infineon TLD5099EP Скачать руководство пользователя страница 15

Trademarks
All referenced product or service names and trademarks are the property of their respective owners.

Edition 2022-02-04
Published by
Infineon Technologies AG
81726 Munich, Germany
 

©

 2022 Infineon Technologies AG

All Rights Reserved.
 
Do you have a question about any

aspect of this document?
Email: 

[email protected]

 
Document reference

IFX-pph1578654908400

IMPORTANT NOTICE
The information contained in this application note is

given as a hint for the implementation of the product

only and shall in no event be regarded as a description

or warranty of a certain functionality, condition

or quality of the product. Before implementation

of the product, the recipient of this application

note must verify any function and other technical

information given herein in the real application.

Infineon Technologies hereby disclaims any and all

warranties and liabilities of any kind (including without

limitation warranties of non-infringement of intellectual

property rights of any third party) with respect to any

and all information given in this application note.
The data contained in this document is exclusively

intended for technically trained staff. It is the

responsibility of customer’s technical departments to

evaluate the suitability of the product for the intended

application and the completeness of the product

information given in this document with respect to such

application.

WARNINGS
Due to technical requirements products may contain

dangerous substances. For information on the types

in question please contact your nearest Infineon

Technologies office.
Except as otherwise explicitly approved by Infineon

Technologies in a written document signed by

authorized representatives of Infineon Technologies,

Infineon Technologies’ products may not be used in

any applications where a failure of the product or

any consequences of the use thereof can reasonably

be expected to result in personal injury.

Содержание TLD5099EP
















Отзывы: