Infineon CDM10V Скачать руководство пользователя страница 1

 

User Manual 

Please read the Important Notice and Warnings at the end of this document

 

V 1.0 

www.infineon.com

 

page 1 of 9 

2017-09-19 

UM_201709_PL21_011 
 

 

COOLDIM_PRG_BOARD 

User manual for CDM10V programming board 

About this document 

Scope and purpose 

CDM10V programming user manual describes the “COOLDIM_PRG_BOARD” burner board usage, the UART 
protocol handling and the fusing details. 

Intended audience 

CDM10V programming board user.  

 

Table of contents 

About this document ....................................................................................................................... 1

 

Table of contents ............................................................................................................................ 1

 

1

 

CDM10V BURNER .................................................................................................................... 2

 

1.1

 

Introduction ............................................................................................................................................. 2

 

1.2

 

Chip orientation ...................................................................................................................................... 2

 

1.3

 

Control buttons ....................................................................................................................................... 3

 

1.4

 

Switches ................................................................................................................................................... 3

 

1.5

 

Connectors / Jumper .............................................................................................................................. 4

 

2

 

Fusing details ........................................................................................................................ 5

 

2.1

 

UART configuration ................................................................................................................................. 5

 

2.2

 

Fusing conditions .................................................................................................................................... 5

 

2.3

 

Fusing procedure .................................................................................................................................... 6

 

Revision history ............................................................................................................................. 8

 

 

 

Содержание CDM10V










Отзывы: