Infineon Technologies TLE5012B Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 105

Infineon Technologies TLE5012B Скачать руководство пользователя страница 64

TLE5012B

SSC Registers

User’s Manual

64

Rev. 1.2, 2018-02

6

SSC Registers

The TLE5012B includes several registers that can be accessed via Synchronous Serial Communication (SSC) to
read data as well as to write to configure settings.

6.1

Registers Overview

There are twenty-two documented registers, but only a few are relevant to read data or to configure the TLE5012B.
Many extra features that are also documented may only be used in very specific cases. In the following bitmap the
relevant bits can be identified.
The most important bits are the ones indicated in green, orange and grey. The green bits contain calculated data;
the bright green bits are additional data that may only be relevant for some specific applications. The orange bits
are configuration parameters, which can be changed if the default values are not the desired ones. The dark
orange bits are relevant if connecting several devices (sensors) to a same master (microcontroller). The grey bits
are relevant for diagnosis to address the demands for functional safety.
There are also yellow bits for the autocalibration and calibration values. Finally the purple bits mark extra features
that can be configured, if desired.

Figure 6-1 Bitmap Part 1

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

STAT (00

H

)

Status Reg.

RD_

ST

S_R

OM

S_A

DCT

Res

S_X

YOL

S_O

V

S_D
SPU

S_FU

SE

S_V

R

S_W

D

S_R

ST

ru

ru

ru

r

r

ru

ru

ru

r

r

r

r

ru

ACSTAT (01

H

)

Activation status Reg.

AS_

FRST

Res

AS_

OV

AS_

FUSE

AS_

VR

AS_

WD

AS_

RST

w

w

w

w

w

w

w

w

w

w

AVAL (02

H

)

Angle Value Reg.

RD_

AV

r

ASPD (03

H

)

Angle Speed Reg.

RD_

AS

r

AREV (04

H

)

Angle Revolution Reg.

RD_

REV

r

FSYNC (05

H

)

Frame Synchro. Reg.

MOD_1 (06

H

)

Interface Mode1 Reg.

CLK_

SEL

Res

w

w

SIL (07

H

)

SIL Reg.

FILT_

PAR

FILT_

INV

FUSE

_REL

w

w

w

w

MOD_2 (08

H

)

Interface Mode2 Reg.

Res

ANG

_DIR

PRED

ICT

w

w

MOD_3 (09

H

)

Interface Mode3 Reg.

SPIK

EF

SSC
_OD

w

w

OFFX (0A

H

)

Offset X Reg.

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

ru

ANG_VAL

ANG_SPD

ru

S_NR

w

Res

NO_

GMR

_A

NO_

GMR

_XY

S_

MAG

OL

AS_
VEC

MAC

AS_

ADC

T

AS_

DSP

U

AS_
VEC
_XY

REVOL

FCNT

wu

ru

FSYNC

TEMPER

ANG_RANGE

AUTOCAL

Res

w

wu

r

FIR_MD

Res

w

w

IIF_MOD

ADCTV_X

w

ANG_BASE

w

w

PAD_DRV

X_OFFSET

Res

w

DSP
U_H

OLD

ADC

TV_E

N

w

ADCTV_Y

w

Res

«
...
62
63
64
65
66
...
»

Содержание TLE5012B










































































































Отзывы:

Нет отзывов