manualshive.com logo in svg

Inficon Sensistor ISH2000 HySpeed, Руководство по эксплуатации

Поделиться
Скачать
Inficon Sensistor ISH2000 HySpeed Скачать руководство пользователя страница 9

Hydrogen leak detector Sensistor ISH2000 

 - 

Operating Manual

 

OM-Sensistor ISH2000-EN-201304

9

EN

2.3   Sensistor ISH2000P

The panel mount model, Sensistor ISH2000P, has identical features of the Sensistor 
ISH2000.

The difference is that the Sensistor ISH2000P can be installed in the operator’s panel 
or any other flat surface. The instrument operates on an ex24VCD power 
supply, provided by the customer. Mounting brackets and a panel rubber seal are 
delivered with the detector. See “Sensistor ISH2000P installation” on page 45.

Fig 2-3. The panel mount model consists of seven parts.

Item

Description

1

Detector instrument

2

Brackets (not shown)

3

Screws (not shown)

4

O-rings seal (not shown)

5

User manual (not shown)

6

User manual in electronic form 
(on CD or USB memory stick)

7

Product return form (not shown)

1

Содержание Sensistor ISH2000 HySpeed



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды