manualshive.com logo in svg

Inficon Sensistor ISH2000 HySpeed, Руководство по эксплуатации

Поделиться
Скачать
Inficon Sensistor ISH2000 HySpeed Скачать руководство пользователя страница 8

Hydrogen leak detector Sensistor ISH2000 

 - 

Operating Manual

8

OM-Sensistor ISH2000-EN-201304

EN

2.2   Sensistor ISH2000C

The battery operated model, Sensistor ISH2000C, has all the Sensistor ISH2000 
features apart from the APC system. This means that only passive probes (for 
example Hand Probe P50) can be used. This is due to power management control. 
The battery, a Li-ion battery at 14.8 V, can not support the current required to 
operate external probes.

On the display a symbol in the upper right corner shows the battery charge status. 
Sensistor ISH2000C will operate for 14 hours on a fully charged battery with 
screensaver and mute function. And 9 hours without screensaver and mute function.

One hour charging will give about one hour of operating time. This can be done 
when necessary, but it is important to regularly fully charge the battery.

Fig 2-2. The battery operated model consists of seven parts.

Item

Description

1

Detector Instrument

2

Hand Probe P50 (shown) or P50-Flex

3

Probe cable C21

4

Carrying case

5

Battery charger (the battery charger are country 
specific and may differ, not shown).

6

User manual (not shown)

7

User manual in electronic form 
(on CD or USB memory stick)

8

Product return form (not shown)

1

2

3

4

Содержание Sensistor ISH2000 HySpeed



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды