manualshive.com logo in svg

Inficon Sensistor ISH2000 HySpeed, Руководство по эксплуатации

Поделиться
Скачать
Inficon Sensistor ISH2000 HySpeed Скачать руководство пользователя страница 21

Hydrogen leak detector Sensistor ISH2000 

 - 

Operating Manual

 

OM-Sensistor ISH2000-EN-201304

21

EN

3- Set

 Leak Gas 

= Helium

Note:

Feed the Calibration leak with hydrogen tracer gas at the pressure stated on 
the Calibration certificate. If another pressure is used you must correlate the 
resulting flow and use this value as 

Calibration Value

.

Note:

The resulted concentration from the Calibration leak should be within the 
concentration range of 5 ppm - 400 ppm H

2.

7.6   Calibration value with Calibration gas

When measuring hydrogen concentration (instead of leak flow) in most cases you 
will calibrate the detector to a Calibration gas with a known concentration.

Set the 

Calibration Value

 equal to the Hydrogen concentration in your Calibration 

gas. This can be found on the certificate of analysis issued for the gas. Also set the 

Calibration Unit

 to ppm.

Example:

 Calibration gas contains 10 ppm Hydrogen in synthetic air.

1- Set the 

Calibration Value

 = 10

2- Set the 

Calibration Unit

 = “PPM”

Содержание Sensistor ISH2000 HySpeed



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды