Inficon 540-200 Скачать руководство пользователя

Страница: 57 / 90

INFICON

Operation | 6

T-Guard2_Operating-instructions-jina85en1-13-(2009)

57 / 90

6.10 Switch off

To switch the device off, disconnect it from the power supply.

NOTICE

Material damage due to helium contamination

Helium remaining in the sensor shortens the service life of the sensor and increases

the warm-up phase.

► Do not switch off the device if the sensor is contaminated with helium. Wait until the

device is ready to measure again (measurement view is displayed).

6.11 Calling up information on the device and on the

measurement

All important information for operation can be displayed on the info menu.

► Select “Info” in the main menu.

Displaying/changing

settings

You can find all the current measurement settings under “View/change settings”. You

can select a setting using the right arrow key and switch to the corresponding setting

window by selecting “Change”.

Settings overview

Fig. 25: Settings overview

Leave the window by selecting “Cancel”. Changed settings are saved.

Internal data

You can display all of the device’s internal data by selecting “Internal data”. You can

switch between the 8 windows using the lower right and left keys .

Vacuum schematic

The image called up displays the device’s vacuum schematic and its valve

arrangement. In addition, sensor pressure, sensor current and an estimated helium

concentration in ppm are displayed.

Interfaces

You can display all information on the interfaces by selecting “Interfaces”. You can

select a setting using the right arrow key and switch to the corresponding setting

window by selecting “Change”.

Содержание 540-200



























































































Результаты поиска

Содержание 540-200

Отзывы:

Похожие инструкции для 540-200

Бренды по названию

Популярные бренды

Inficon 540-200, Перевод оригинальной инструкции по эксплуатации

Результаты поиска

Содержание 540-200

Отзывы:

Похожие инструкции для 540-200

Бренды по названию

Популярные бренды