Inficon 540-200 Скачать руководство пользователя

Страница: 42 / 90

6 | Operation

INFICON

42 / 90

T-Guard2_Operating-instructions-jina85en1-13-(2009)

6.4.4 Calibrate

NOTICE

Incorrect calibration because of unsuitable calibration leak

An unsuitable calibration leak leads to an incorrect calibration and therefore to

incorrect measurement results.

► An accurate calibration is achieved with client-specific calibration leaks by

INFICON.

► Ideally, produce a master test object with a built-in calibration leak.

► The calibration leak rate must be greater than half of trigger level 1. Possible leak

rates are 5 × 10

-6

bis 15 mbar l/s.

The device must be calibrated before the first measurement.

Calibration is only possible after the device has completed the warm-up phase. Before

this point, the relevant menu item is not displayed.

In the following operation, you only need to calibrate again if the measurement setup

or the measurement conditions are changed:

• Accumulation measurement:

– Change to the accumulation volume

– Change to the measurement time for manual measurement time entry

– Change to the trigger value

• Carrier gas measurement

– Change to the carrier gas flow

– Change to the measurement time for manual measurement time entry

The measurement time during the calibration is set automatically. You can change the

measurement time if necessary; a shorter measurement time, however, leads to lower

reproducibility (“Measurement settings > Set times > measurement time”).

Fig. 19: Access to the calibration settings

Содержание 540-200



























































































Результаты поиска

Содержание 540-200

Отзывы:

Похожие инструкции для 540-200

Бренды по названию

Популярные бренды

Inficon 540-200, Перевод оригинальной инструкции по эксплуатации

Результаты поиска

Содержание 540-200

Отзывы:

Похожие инструкции для 540-200

Бренды по названию

Популярные бренды