Inficon 540-200 Скачать руководство пользователя

Страница: 30 / 90

5 | Installation

INFICON

30 / 90

T-Guard2_Operating-instructions-jina85en1-13-(2009)

5.3 Connecting an external control unit

NOTICE

Material damage due to connection error.

If you insert or remove the plug during operation, the device could be damaged.

► Only insert or remove the cable when the device is disconnected from the power

supply.

The diagram below displays the dimensions of the control unit for rack installation.

Fig. 11: Dimensions of the control unit for rack mounting

The front of the control unit for rack installation corresponds to protection class IP40.

• Place the table device on a stable base or mount the control unit in a rack.

• Connect the external control unit to the “CONTROL UNIT” connection on the T-

Guard2 using the corresponding cable.

• Secure the plug on the socket by tightening the screws.

Содержание 540-200



























































































Результаты поиска

Содержание 540-200

Отзывы:

Похожие инструкции для 540-200

Бренды по названию

Популярные бренды

Inficon 540-200, Перевод оригинальной инструкции по эксплуатации

Результаты поиска

Содержание 540-200

Отзывы:

Похожие инструкции для 540-200

Бренды по названию

Популярные бренды