infaco A3M V2.0 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 32

infaco A3M V2.0 Скачать руководство пользователя страница 13

12

13

Do not leave your battery on charge for more than 15 hours

The battery has sufficient autonomy to complete between 7000 and 8000 ties.

If you are thinking of doing more than 8000 ties a day, we advise you to:

1. Either recharge the battery for at least an hour during your lunch break
to achieve extra autonomy of approximately 3000 ties.
2. Or buy the 2-battery option.

N.B. a few minutes before your battery is completely discharged, the A3M V2 may
lose speed or no longer cut the wire.

Disconnect connector 03 on the A3M V2 from the battery (connector 02).
Connect plug 04 on the charger to the 230 V 50 Hz supply in a well-ventilated
room free of inflammable products and sources of ignition.

Connect connector 01 on the charger to connector 02 on the battery.

The charger starts to work automatically as soon as the battery is connected. Indi-
cator light 05 remains lit throughout charging. It starts flashing when your battery
is fully charged. If the indicator light on your charger does not light up, leave your
battery connected and, at the same time, disconnect the plug (230 V) from your
charger and re-connect it until the orange indicator lights light up.

For information, it takes about 5 hours to charge up the battery belt.

RECHARGING

THE BATTERY

Charger

04

05

01 02

03

Battery pack

A3M V2

Tool cary bag

«
...
11
12
13
14
15
...
»

Содержание A3M V2.0

































Отзывы:

Нет отзывов