Assembly Instructions
INCRA Wheel Kit
1
Assembly Instructions for the INCRA Wheel Kit
Fig. 1 Wheel Kit
w w w. i n c r a . c o m
(1) Front Wheel Connector Bracket
(1) Front Wheel Pedestal
(1) Front Wheel Foot Pedal
(1) Front Wheel Caster
(2) Leg Wheel Bracket
(2) Leg Wheel
(8)
1/4
-20 x
1/2
Hex Bolt
(2)
1/4
-20 x 2
1/4
Hex Bolt
(6)
5/16
-18 x
1/2
Hex Bolt
(2)
5/16
-18 x 3
3/4
Hex Bolt
(8)
1/4
-20 Square Nut
(2)
1/4
-20 Locking Nut
(6)
5/16
-18 Hex Nut
(2)
5/16
-18 Locking Nut
(11)
1/4
” Flat Washer
(4)
1/4
” Lock Washer
(4)
1/4
id x
1/4
Thick Nylon Washer
(4)
5/16
id x
3/16
Thick Nylon Washer
Parts List:
Step 1. Assemble Leg Wheels.
First, loosley install two sets of
1/4
-20 x
1/2
bolts,
1/4
-20 square
nuts and
1/4
” washers in each wheel bracket as shown in
Fig. 2
.
Second, install a rubber wheel in the lower hole on each wheel
bracket using the
1/4
-20 x 2
1/4
hex bolt,
1/4
-20 locking nut,
1/4
”
steel washer and
1/4
” thick Nylon washers as shown in
Fig. 2
.
Be sure that the two
1/4
” thick Nylon washers are against the hub
of the wheel and positioned INSIDE the wheel bracket.
Install,
but do not fully tighten the locking nut on the 2
1/4
hex bolts
at this time
.
Step 2. Install Leg Wheels on Legs.
Orientation: When mounting the stand to offset tables, the two
leg wheels should be located under the end of the table WITH
the router cutout in it. For center mount router tables, the two
leg wheels can be on either end of the table.
Remove the levelers from the two legs on which the wheels will
be installed. As shown in
Fig. 3
, slide the (2) square nuts and
the long hex bolt head on each wheel assembly into the T-slot
on the leg extrusion. Adjust the vertical position of each wheel
for stability, then firmly tighten all bolts. Tighten the locking nut
enough to remove all side play between the wheel and the
inside of the wheel bracket, but still loose enough for the wheel
to pivot freely.
Fig. 2 Assemble Leg Wheels
Fig. 3 Install Leg Wheels
Table Stand Legs
Leg Wheel (2)
Wheel Stringer on Table Stand
Leg Wheel Bracket (2)
Front Wheel Foot Pedal
Front Wheel Caster
Front Wheel Pedestal
Front Wheel Connector Bracket
Leg Wheel Bracket
Wheel
1/4
-20
Square Nut
1/4
-20 x 2
1/4
Hex Bolt
1/4“
Thick Nylon Washer
1/4“
Thick Nylon Washer
1/4“
Washer
1/4
-20
Locking Nut
1/4
-20 x
1/2
Hex Bolt (4)
1/4“
Washer (4)
Outfeed Wheel
Assembly
Capture Square
Nuts & Hex Bolt
in T-Slot on Leg
Infeed Wheel
Assembly
Leg Wheel (2)
