Impulse Yamuna Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 38

background image

8

3

Lifting instructions YAMUNA pump unit

DANGER
Never walk under a raised load. This can result in a life-threatening situation.

WARNING
Always disconnect all external connections before moving the pump unit.

WARNING
Neither the lifting eye on the engine nor the lifting eye of the (bare shaft) pump may
be used for transport of the pump unit.

WARNING
Lifting forces must be as vertical as possible; the maximum lifting angle is 15°.

There is a lifting eye located on the top of the enclosure. Only lift the unit from this lifting eye.

WARNING
If the pump unit is installed on a swampy or muddy surface, the installation may
be ‘stuck’ to the ground.

DANGER
NEVER move or lift the pump unit by the angle profiles on top of the enclosure or
stacking frame.

«
...
6
7
8
9
10
...
»

Содержание Yamuna







































Отзывы:

Нет отзывов

Похожие инструкции для Yamuna

Бренд: Watson-Marlow Страницы: 55

Бренд: GE Страницы: 28

Бренд: Zehnder Pumpen Страницы: 24

Бренд: Walchem Страницы: 31

Бренд: Walrus Pump Страницы: 8

Бренд: A.O. Smith Страницы: 6

Delta Solo Compact MVP Series

Бренд: KSB Страницы: 40

Бренд: Barnstead|Thermolyne Страницы: 56

Бренд: Atlas Copco Страницы: 137

Бренд: A.O. Smith Страницы: 119

Shurflo 8000 Series

Бренд: Lilie Страницы: 6

CLIMAGUARD TX23

Бренд: McLean Страницы: 20

Бренд: Gorenje Tiki Страницы: 48

Бренд: nedis Страницы: 60

Бренд: OSNA Страницы: 40

Бренд: Swim & Fun Страницы: 136

Бренд: Xylem Страницы: 54

Бренд: Xylem Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды