Impulse Yamuna Скачать руководство пользователя

Страница: 37 / 38

12. Troubleshooting table

WARNING
In the event of a malfunction or abnormal operation, shut off the pump immediately
to prevent a dangerous situation and/or damage to the unit.

Malfunction

Probable cause

Diagnose

Possible solution

Insufficient output

Dry pump housing

Screaming sound with
every pump movement

Fill the pump housing
with at least 10 liter of
water (1 bucket)

Worn out collars

Check the state of the
collars through
inspection covers 4 & 7

Replace the collars

Defect suctionvalves

Remove inspection
covers 2 & 5 and check
for defects

Remove any blokages
or worn out/broken
parts

Insufficient suction
capacity during
commission

Stonebox is polluted

Check the stonebox
through cover 6

Clean the stonebox

Leakage through
inspection cover gaskets

Hissing sound
during/right after
commission near point
1,2,4,5,6 or 7

Tighten or replace
leaking gasket

Leaking stuffing box
packing

Hissing sound near
Stuffing box (3)

Adjust the gland plate

Defect discharge valves

Remove inspection
window 1 & 2 and
check for defects

Remove any blokages
or worn out/broken
parts

Worn out collars

Check the state of the
collars through
inspection covers 4 & 7

Replace the collars

Inspection covers for
discharge valves

Inspecttion covers for both
suction and discharge valves

Gland plate

Inspectioncover for rear
collars

Inspectioncover for suction
valves

Stonebox cleaning window

Inspection cover front
collars

Содержание Yamuna







































Результаты поиска

Содержание Yamuna

Отзывы:

Похожие инструкции для Yamuna

Бренды по названию

Популярные бренды

Impulse Yamuna, Инструкция по эксплуатации и технике безопасности

Результаты поиска

Содержание Yamuna

Отзывы:

Похожие инструкции для Yamuna

Бренды по названию

Популярные бренды