background image

WARRANTY: 

Impact Canopy strives to bring products to the market that are superior free of defect. We are confident that you will be 
completely satisfied with your canopy / carport. Listed below are precautions that should be taken to ensure proper 
safety and use of your unit.  

 

This structure is designed for temporary use and not recommended during extreme weather conditions or as a 
permanent structure. Ensure that the frame is properly anchored and remove the cover during extreme weather 
conditions. This structure is not designed for high winds or heavy snow fall. 

-

 

Keep all direct flame and heat sources away from fabric. The fabric is treated with fire retardant coating but 
will burn / melt if left in continuous contact with any flame source.  

Care Instructions: Use warm water, soap and a light brush or cloth to clean the fabric of this canopy / carport.  

-

 

Do NOT use Bleach, Dry Clean, or Machine Wash the cover or sidewall enclosure kit  

-

 

Do Not hang or suspend anything to the frame, cover, or grommets of the unit.  

-

 

Immediately remove and rain or snow accumulation on the cover. This can cause the cover to fault, rip, or 
collapse the roof.  

-

 

Removing, water, snow or ice accumulation; by using a ladder and brush away from the top of the cover. Do 
not stand under the unit and push the cover up to remove. This can be dangerous if the cover or frame 
happen to collapse from the weight of the water, snow or ice.  

 

Содержание 070018151







Отзывы: