D
B
I
2
1
-
8
0
H
3
I
__________________________________________________________________________________________________________________________________________________
0
1
0
2
/
2
1
/
5
Page 1 of 5
INTRODUCTION
i3H provides:
Powerful Standard Features
in
one
unit including
Controller
Network
Operator Interface
Highly Visual Display Screen
.
Standard Features on i3H
Base
Model
Network
Screen Type
Standard
Features
i3H08
On-Board
Ethernet
100BaseT
8.4” TFT SVGA
with 32,768
colors
CompactFlash
3 Serial Ports
Ethernet
i3H10
10.4” TFT
SVGA
with 32,768
colors
i3H12
12.1” TFT
SVGA
with 32,768
colors
2
Specifications / Product Descriptions
Table 2 – i3H Base Specifications
Base Models
i3H08
(8-inch) (SVGA)
i3H10
10-inch) (SVGA)
i3H12
(12-inch) (SVGA)
Display Type
(LCD with
backlight)
800 x 600
TFT
800 x 600
TFT
800 x 600
TFT
Display Size
8.4”
10.4”
12.1”
Display Screen
Dimensions
6.7”W x 5”H
(170 x 128 mm)
8.3“W x 6.2“H
(211 x 159 mm)
9.7“W x 7.3“H
(246 x 185 mm)
Display Memory
8 MBytes
User Keys
7 configurable keys + System Key
Screens
Supported
1,023 screens
(300 objects per screen)
Number of
Colors
32,768
3
INSTALLATION
Base
Models
i3H08
(8-inch)
i3H10
10-inch)
i3H12
(12-inch)
Primary
Power
Voltage:
24 VDC (+/-10%)
Steady State
Current:
0.625 A @ 24 VDC
Inrush Current:
(25 A @ 24 VDC)
for 0.7 ms
Voltage:
24 VDC (+/-10%)
Steady State
Current:
1.25 A @ 24 VDC
Inrush Current:
(30 A @ 24 VDC)
for 1 ms
Voltage:
24 VDC (+/-10%)
Steady State Current:
1.25 A @ 24 VDC
Inrush Current:
(30 A @ 24 VDC)
for 1 ms
i3H Dimensions
See
Panel Cut-outs and Dimensions
for complete details (Section 3.2)
Base
Models
i3H08
(8-inch)
i3H10
10-inch)
i3H12
(12-inch)
Height
7.0” (178 mm)
9.09” (230.9 mm)
10.25” (260.4 mm)
Width
9.17” (233 mm)
11.95” (303.5 mm)
12.87” (326.9 mm)
Mounting
Depth
2.35” (59.70 mm)
2.52” (64 mm)
2.52” (64 mm)
Keypad
Material
Faceplate made of Lexan HP92 by GE Plastics.
The material is resistant to most corrosive substances found in
industrial environments. The material also holds up well in most
industrial conditions.
Serial Ports
3 RS-232 / RS-485 Ports. Software Selectable.
Network
Options
On-board Ethernet 100BaseT
Control
Memory
256K Ladder Memory plus 32KB Register Space
Control
Scan Rate
0.2mS / K Ladder Logic (typical)
Portable
Memory
Compact FLASH (CF) slot
Temperature
& Humidity
32 - 122
°
F (0 - 50
°
C), 5 to 95% Non-condensing
UL
Please contact IMO for certificate information
CE
i3H Series Models:
i3H08/00000-SEOL -
8
”
display model
i3H10/00000-SEOL -
10
”
display model
i3H12/00000-SEOL -
12
”
display model
Note:
Prior to mounting, observe requirements for the panel layout design and adequate clearances in the
I3 Hardware Manual
. A handy checklist is provided in the
Installation
chapter.
3.1
Installation Procedures
a.
i3H Base Installation
1.
Per specifications of the I3H model you are using, carefully prepare the panel cutout. Make sure the corners of the cutout are square and free from burrs. (Locate the panel
cut-outs and dimensions that pertain to your I3H model as shown in this document.)
2.
Cut the host panel
3.
Insert the i3H (base unit only) through the panel cutout from the front. The gasket material needs to lie between the host panel and the I3H.
4.
Install and tighten the mounting clips (provided with the I3H) until the gasket material forms a tight seal.
5.
Connect cables as needed such as communications, programming, power and fiber optic cables to the I3H ports using the provided connectors.
6.
As a final step before using, carefully remove the protective, plastic sheet from the front of the unit. The protective, transparent sheet is used to protect the display window.
7.
Begin configuration procedures for the I3H.
Caution: Do not force the I3H into the panel cutout. An incorrectly sized panel cutout damages the I3H screen.
Caution: Do not over-tighten. Over-tightening damages the case.
