Imagine DQS6800+ Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 84

background image

DQS6800

+

Installation and Operation Manual

15

Chapter 2: Installation

Upgrading Module Firmware

Firmware upgrading is a routine procedure that you must perform to
install newer versions of software on 6800

+

modules. CCS Pilot,

CoPilot, or Navigator software version 3.1.1 or later is required for this
procedure. The frame must contain or be connected to another frame
that contains an ICE6800

+

or a 6800

+

ETH module.

In the unlikely event that the upgrade fails (because of such situations
as network interruptions, power failures, etc.), the module may not
respond to controls and will appear to be non-functional. In that event,
follow the procedures described in

“Correcting a Failed Upgrading

Procedure” on page 18

.

Upgrading the Firmware

You can upgrade your 6800

+

module’s firmware using the Software

Upgrade tool. This tool is included with CCS Pilot, Co-Pilot, or
Navigator software version 3.1.1 or later.

Caution

The File Transfer tab is not meant to be used for firmware
upgrades. For best results, use the Software Upgrade tool to
upgrade module firmware.

To upgrade your module’s firmware, follow these steps:

1. Download the most recent appropriate upgrade package from our

website or from your CD-ROM.

2. If the affected module has not been discovered, perform the

Discovery operation, as described in

“Discovering Your Module

Using CCS Software” on page 31

Note

Information about discovering modules can also be found in
your CCS software application manual or online help. (If you
cannot discover the device, see

“Manually Adding a Device to

the Discovery or Network Folder” on page 19

3. From the

Tools

menu, select

Software Upgrade

.

«
...
27
28
29
30
31
...
»

Содержание DQS6800+





















































































Отзывы:

Нет отзывов

Похожие инструкции для DQS6800+

Бренд: Barco Страницы: 2

Бренд: Patton electronics Страницы: 11

Parallel Port Input/Output Converter PPIO

Бренд: B&B Electronics Страницы: 34

Бренд: S.M.S.L Страницы: 31

Бренд: tams elektronik Страницы: 26

Бренд: D&R Страницы: 17

PROWATT SW SW 1000

Бренд: Xantrex Страницы: 38

Бренд: Hagerman Audio Labs Страницы: 6

Бренд: OSEE Страницы: 46

Бренд: Autonics Страницы: 6

BRAVO ST 230 VAC

Бренд: Helios Power Solutions Страницы: 39

Бренд: Autarco Страницы: 37

Бренд: Avonic Страницы: 6

Бренд: Audioplex Страницы: 2

Бренд: Partilink Страницы: 30

Бренд: Samlexpower Страницы: 48

Бренд: AEG ID Страницы: 20

Бренд: Wellav Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды