background image

MILLENIUM FREESTANDING MANUAL 2014

Q u a l i t y   &   Va l u e   I n   G a s   L o g   F i r e s

Your new ILLUSION Millenium Gas Space Heater is fitted with a THERMOSTATICALLY 

CONTROLLED fan.

 

EXPLANATION

What this means is that other than initially setting the fan to the desired position,ie: Low High or 

Boost, it will no longer be necessary to turn the fan on or off whilst the unit is operating.

STARTUP

The new thermo switch will automatically turn the fan on when the heater has reached a 

predetermined temperature. This will usually be 10 to 15 minutes after the heater is turned on.

It is important to let the customer know that there is nothing wrong with the heater, in fact it is 

much more convenient and energy saving method of operating the fan.

SHUT DOWN

It will also shut down the fan 10 to 15 minutes after the heater is turned off, once the firebox has 

cooled sufficiently.

REMOTE CONTROLLER OPTION

The above features apply even if the unit is fitted with a new 

OPTIONAL

 remote controller. If the 

remote control is used to turn the appliance on, the fan will only startup if the fan speed is set to 

LOW, HIGH OR BOOST, in which case the fan will turn on when the unit reaches temperature (10 

to 15 minutes). If the remote controller is used to turn the heater off, the fan will shut down when 

the heater has cooled. (10 to 15 minutes). If the remote control is set to turn off the appliance at a 

specified time, the fan will contiue to operate until the firebox has cooled, again usually 10 to 15 

minutes. The fans speeds can still be adjusted manually whilst the unit is operating.

18

THERMOSTATICALLY CONTROLLED FAN

Содержание MILLENIUM UGL32LP


























Отзывы: