Sliding Door Double Cylinder Lock
Very Important!
Please fasten all screws by hand and not an electric screwdriver or drill, as over tightening is not recommended.
Step 2: Installation of Handle - Please note the Black Markings on Cylinders and Tail Pieces. In order for this lock to work
properly, all 4 markings must be facing each other as shown below, with the keys removed.
Remove screws from the Handle to separate it from the Lock Chassis. On a Double Cylinder lock,
install both the inside cylinder and the outside cylinder. Feed the Tail Piece through the Cylinder
Locator and attach the locator on the Outer Pull. The Tail Piece length is adjustable to suit door
thicknesses. Snap at break marks for desired length. Now select two screws to suit your door
thickness. • Use 2 x 55mm screws if your Door is 30-35mm thick, • Use 2 x 50mm screws if your
Door is 24-30mm thick or • Use 2 x 45mm screws if your Door is 18-25mm thick.
Insert your selected length screw through the Lock Chassis through the door and into Handle by
hand. The 4 screws remaining can be disposed of.
Instructions to install the Sliding Door Double Cylinder Lock.
If installing this lever set into a new door, you will need the following tools: 3mm pilot hole, 9mm drill bit, corded or cordless drill, hammer, wood chisel, Phillips head screwdriver, tape
and pencil.
If you are replacing an existing lock, remove your existing lock, clean down surfaces and follow the Installation process.
WARRANTY CONDITIONS
Any claim under this warranty must be made within 3 years of the date of purchase of the product. To make a claim under the warranty, take the product (with proof of purchase) to any Bunnings store (see www.bunnings.com.au for store locations). Romak
Hardware Distributors Pty Ltd bears reasonable, direct, expenses of claiming under the warranty. You may submit details and proof to our store for consideration. The warranty covers manufacturer defects in materials, workmanship and finish under normal
use. This warranty is provided in addition to other rights and remedies you may have under law: our goods come with guarantees which cannot be excluded under the Australian Consumer Law. You are entitled to replacement or refund for a major failure and
compensation for other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The warranty excludes damage resulting
from product misuse or product neglect. The warranty covers domestic use only and does not apply to commercial applications. This warranty is given by Romak Hardware Distributors Pty Ltd, ABN 15489950457, 177-181 Atlantic Drive, Keysborough Vic 3173,
(03) 9795-6789, e-mail: [email protected]
Suits models 697460, 697470, 697480.
00566
Step 3: Installing Keeper and Striker
Unscrew the Jacking Screw and loosen
the Fixing Screws.
Separate the Keeper from Striker.
Line up the Striker with the Lock
Chassis on an adjacent door frame.
Fasten the Striker to the door frame
with screws.
Reassemble the Keeper and Striker.
Fixing Screws can be used to adjust
Striker up and down to better fit the
Beak locking mechanism.
Step 1: Preparation
Correctly place template and fold
on line A. Tape it to your sliding door
face, at the desired height from the
floor level, ensuring that a position
is selected either above or below the
existing screen door handle so that
the handles don’t interfere with each
other. Drill marked holes using a 3mm
pilot hole followed by 9mm drill bit and
continue with the installation.
Lock Chassis
Handle
Black Markings
Outside Cylinder
Inside Cylinder
Beak
Cylinder Locator
Door
Tail Piece
Outer Pull
Screw
Latch Lever
Black Markings
Striker
Keeper
Fixing Screw
Jacking Screw
Adjacent
Door Frame
Line A
25mm
Line A
Fold to Door Edge
25 mm
Lock Chassis
Handle
Black Markings
Outside Cylinder
Inside Cylinder
Beak
Cylinder Locator
Door
Tail Piece
Outer Pull
Screw
Latch Lever
Black Markings
Striker
Keeper
Fixing Screw
Jacking Screw
Adjacent
Door Frame
Line A
25mm
Line A
Fold to Door Edge
25 mm
Lock Chassis
Handle
Black Markings
Outside Cylinder
Inside Cylinder
Beak
Cylinder Locator
Door
Tail Piece
Outer Pull
Screw
Latch Lever
Black Markings
Striker
Keeper
Fixing Screw
Jacking Screw
Adjacent
Door Frame
Line A
25mm
Line A
Fold to Door Edge
25 mm
Lock Chassis
Handle
Black Markings
Outside Cylinder
Inside Cylinder
Beak
Cylinder Locator
Door
Tail Piece
Outer Pull
Screw
Latch Lever
Black Markings
Striker
Keeper
Fixing Screw
Jacking Screw
Adjacent
Door Frame
Line A
25mm
Line A
Fold to Door Edge
25 mm
Lock Chassis
Handle
Black Markings
Outside Cylinder
Inside Cylinder
Beak
Cylinder Locator
Door
Tail Piece
Outer Pull
Screw
Latch Lever
Black Markings
Striker
Keeper
Fixing Screw
Jacking Screw
Adjacent
Door Frame
Line A
25mm
Line A
Fold to Door Edge
25 mm
00566-001_SLIDING DOOR LCK IKONIC DBL CYL 697460_697470_697480 - Instruction LEAFLET-V1.indd 1
16/08/13 9:57 AM
