background image

26

Error codes

Any malfunctions during operation will be identified by an error message on the display�
Proceed as follows in such cases:

 Switch off device using the main switch at the back of the device�

 Carry out corrective measures�

 Restart device�

Error code

Effect

Cause

Solution

Error 01

Pump off
Refrigerating off

No external temperature sensor

- Check this sensor

Error 02

Pump off
Refrigerating off

Motor over current (rate current) - Reduce pump motor speed

- Use fluid with lower viscosity
- Check if the pump impeller is blocked

Error 04

Pump off
Refrigerating off

Motor hall signal missing

- Reduce pump motor speed
- Use fluid with lower viscosity
- Check if the pump impeller is blocked

Error 06

Pump off
Refrigerating off

Too low liquid level

- Check the liquid level and buoyage

Error 10

Pump off
Refrigerating off

PC communication failure 

- Check communication cable

Error 15

Pump off
Refrigerating off

Compressor power supply 
disconnected

- Restart the device

Error 16

Pump off
Refrigerating off

Suction temperature error 

 

- Restart the device

Error 17

Pump off
Refrigerating off

Discharge temperature  error  

- Restart the device

Error 19

Pump off
Refrigerating off

Fluid temperature too high

- Switch the device off and let the fluid cool down

Error 20

Pump off
Refrigerating off

Condenser fan error

- Restart the device

If the actions described fails to resolve the fault or another error code is displayed then take one of the following steps: 
- Contact the service department
- Send the device for repair, including a short description of the fault� 

Содержание RC 2 GREEN control































Отзывы: