IKA AMM36 страница 18 Скачать руководство пользователя | Manualshive

Страница: 18 / 56

background image

AMM36 • SSI, BiSS, & RS-485

Step 5

Rotate the motor shaft until the code disk

3

is aligned with the encoder unit

5

as shown in the Figure; the mark

8

punched in the code disk

3

must be centred

in the encoder unit

5

as shown in the Figure. Max. misalignment allowed: ± 10

mechanical degrees.

WARNING

If you do not align the code disk

3

with the encoder unit

5

, the encoder will

send back an error at power-on. Should this happen, switch the power supply
off, align the code disk

3

properly and then proceed again as explained in the

next step.

Step 6

Connect the

EC000026

cable to the Hirose connector

9

of the encoder unit

5

.

Please make sure that the power supply is off and the battery is not wired
before connecting the cable.

Step 7

Connect the battery.

Step 8

Switch the power supply on. The LEDs will blink for a while and then go off, if
the installation procedure is successful.
If at the end of the operation a LED is still on, please repeat the procedure again.
Refer also to the “9 - Diagnostic LEDs” section on page 51.

MAN AMM36 SSI_BiSS_RS485 E 1.0.odt

3 - Mounting instructions

18 of 56

«
...
16
17
18
19
20
...
»

Содержание AMM36

























































Отзывы:

Нет отзывов

Похожие инструкции для AMM36

Бренд: Samsung Страницы: 2

Бренд: Danfoss Страницы: 7

Бренд: Danfoss Страницы: 16

VLT 2800 Series

Бренд: Danfoss Страницы: 34

VLT AutomationDrive FC 300

Бренд: Danfoss Страницы: 60

VLT 5000 Series

Бренд: Danfoss Страницы: 63

Бренд: Yamaha Страницы: 2

Бренд: Redgum Страницы: 12

Бренд: Schumacher Страницы: 45

Бренд: Tripp Lite Страницы: 4

Бренд: OCULUS Страницы: 28

Бренд: GME Страницы: 21

Бренд: E-matic Страницы: 22

Бренд: Extron electronics Страницы: 6

Бренд: Boss Audio Systems Страницы: 5

Бренд: M-Audio Страницы: 20

Basys Controls QD1010b

Бренд: TCS Страницы: 5

Бренд: Volt Polska Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды