background image

901176-00 NC

14

ihp.us.com

Grand Canyon Gas Logs, LLC|3515 E. Atlanta Ave. Phoenix, AZ 85040| (602)344.4217 

Remote Operations 

LEARNING TRANSMITTER TO RECEIVER 

Each transmitter uses a unique security code. It will be necessary to press the LEARN button on the receiver to 

accept the transmitter security code upon initial use, if batteries are replaced, or if a replacement transmitter is 

purchased from your dealer or the factory. In order for the receiver to accept the transmitter security code, be sure 

the slide button on the receiver is in the REMOTE position; the receiver will not LEARN if the slide switch is in the 

ON or OFF position. The LEARN button in located on the front face of the receiver; inside the small hole labeled 

LEARN. Using a small screwdriver or end of a paperclip gently press and release the black LEARN buttoninside 

the hole.

When you release the LEARN button the receiver will emit an audible “beep”. After the receiver emits the 

beep press the transmitter ON button and release. The receiver will emit several beeps indicating that the 

transmitter’s code has been accepted

into the receiver.

Содержание DUALBURNER24N























Отзывы: