FCC Information
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment.
This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
• Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
• NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
ISED Information
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
The device comply with ISED RF exposure requirement, users can obtain Canadian information on RF
exposure and compliance.
This equipment should be installed and operated with a minimum distance of 20 cm between the
radiator and your body.
Any Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Cet équipement est conforme aux limites d'exposition aux radiations IC CNR-102 établies pour un
environnement non contrôlé.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
L'appareil est conforme aux exigences d'exposition RF ISED, les utilisateurs peuvent obtenir des
informations canadiennes sur l'exposition aux RF et la conformité.
Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.
Tout changement ou modification non expressément approuvé par la partie responsable de la conformité
peut annuler l'autorité de l'utilisateur à utiliser l'équipement.
CAN ICES-3(B) / NMB-3(B)
DC 5V/2A
-1 +1 auto
DST
usb charging
RESET
RESETRESET
RESET
TEST
TE
ST
TEST
TEST
IMPORTANT SAFETY INSTRUCTIONS
Please heed all warnings, read and follow all instructions and keep these
instructions handy for future reference.
1. Do not use this product near water.
2. Unplug unit and clean only with damp cloth. Stronger cleaning agents, such
as Benzene, thinner or similar materials can damage the surface of the unit.
3. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
4. Heat – This product should be situated away from heat sources such as
radiators, heat registers, stoves or other appliances (including amplifiers)
that produce heat.
5. Only use attachments/accessories specified by the manufacturer.
6. Unplug this product during lightning storms or when unused for long periods
of time.
7. Damage Requiring Service – This product should be serviced by qualified
service personnel when:
- Plug has been damaged.
- Objects have fallen into or liquid has been spilled into the enclosure.
- The unit has been exposed to rain. The unit has been dropped or the enclosure
damaged.
- The unit exhibits a marked change in performance or does not operate
normally.
8. No naked flame sources, such as lighted candles, should be placed on this
product.
9. Attention should be drawn to the environmental aspects of battery disposal.
Many electronics retailers now recycle batteries and other electronic
components at no charge. To find a drop-off location near you, visit
www.call2recycle.com
10. This product is suitable for use in tropical and/or moderate climates.
WARNING:
- To reduce the risk of fire or electric shock, do not expose this product to rain
or moisture.
- Do not dispose of batteries in the household trash or fire.
- The mains plug of power adaptor is used as the disconnect device, it shall
remain readily operable.
iZBT3 - QSG (English)
Size: 510x 150 mm (folded 102 x 150 mm)
Material: 157g Art paper
Color: 1C + 1C (black)
Mar. 05, 2021
8
2
BOTTOM PANEL
OVERVIEW
DISPLAY
7
6
iZBT3QSG-030521-A
Printed in China
© 2021 SDI Technologies, Inc. All rights reserved.
Questions? Visit www.ihome.com
3
4
1
QUESTIONS? visit www.ihome.com
Bedside Sleep Therapy Machine
with Sunrise Wakeup
Model: iZBT3
GETTING STARTED
Connect the included AC adapter to
the DC jack located on the bottom of
the unit and connect the other end to a
working wall outlet not controlled by a
light switch. Remove the battery pull
tab from the bottom of the unit. Press
Power
to turn the unit ON.
1. Connecting the Unit
1. Press and hold the
Time Set Button
until the display flashes. Release the
Time Set Button
.
2. Press the
–
or
+ Buttons
to adjust the
time and tap
Time Set
to confirm
(make sure to set correct AM/PM
time).
3. Press the
–
or
+ Buttons
to adjust the
year, and tap
Time Set
to confirm.
4. Press the
–
or
+ Buttons
to adjust the
month, and tap
Time Set
to confirm.
5. Press the
–
or
+ Buttons
to adjust the
date, and tap
Time Set
to confirm
clock settings.
By default, the DST Switch is set
to Auto and will automatically
adjust the time in March and
November.
5
TURNING THE ALARM ON/OFF
Preview the Alarm
: Press and release the corresponding
Alarm
Button (Light or Sound)
to preview the alarm time.
Arm/Disarm
: Press and release the corresponding
Alarm Button
(Light or Sound)
TWICE to toggle the alarm ON and OFF, indicated
by the related LED indicator.
When the alarm sounds, press the corresponding
Alarm Button
(Light or Sound)
or the
Power/Alarm Reset Button
to disable the
alarm and reset it for the next day.
SNOOZE
When the alarm is sounding, press the
Snooze/Dimmer Button
to
snooze (default is 9 minutes).
DISPLAY AUTO DIMMER
This unit is equipped with a sensor that will automatically adjust the
brightness of the clock display based on ambient light in your room.
When the room is well lit, the display will adjust to Hi brightness for
better visibility. In a dark room, it will dim to a lower brightness. You
can adjust the “lower limit” of the Auto-dimmer to fit your personal
preference of display brightness in a dark room.
The 3 options are:
“Auto 2”
– minimum brightness setting will be level 2
“Auto 1”
- minimum brightness setting will be level 1
“Auto 0”
– clock display will turn FULLY OFF in a dark room
To adjust Dimmer settings:
Press the
Snooze/Dimmer Button repeatedly
to cycle through
brightness levels: Auto 1, Auto 2, Auto 0, Hi, 3, 2, Lo, or OFF.
(Note: choosing
Hi, 3, 2, Lo
, or
OFF
are fixed settings and will not
auto-adjust.)
PROGRAMMABLE SNOOZE
Set the duration of your snooze timer:
1. To program Snooze, press and hold the
Snooze/Dimmer Button
for 2 seconds during normal operation (when no alarm
is sounding). Release the button.
2. Press the
–
or
+
Buttons
to select the desired snooze time
(between 3 and 29 minutes).
3. Press
the
Snooze/Dimmer Button
again to confirm setting.
BATTERY BACK-UP
The unit uses a CR-2450 back-up battery to provide continuous
alarm operation and clock settings in the event of a temporary power
failure. Remove the battery pull tab before use. When ‘Lo Batt’
flashes on the clock display, it is time to replace the back-up battery.
The battery compartment is located on the bottom of the unit.
1. Make sure the AC adapter is
connected, or you will lose your
time and alarm settings during
battery replacement.
2. Use a Phillips screwdriver to open
the battery compartment door.
3. Insert a fresh CR-2450 battery,
checking that the polarity match
the markings on the unit. Replace
the compartment door. Do not
overtighten.
3. Setting Your Clock
For product support information and warranty please visit:
www.ihome.com/support
DST Switch
(Daylight Savings)
Battery Backup
(remove pull tab before use)
Model: iZBT3
SUNRISE
volume
display dimmer
set light
alarm reset
power
TOP PANEL
DC 5V/2.3A
-1 +1 auto
DST
usb charging
BACK PANEL
Tip:
To toggle between 12/24
hour time displays, press the
Sound Alarm Button or the Light
Alarm Button while in Time Set
mode.
LIGHT THERAPY
SOUND THERAPY
1.
Press and hold
the
Sound Alarm Button
for 2 seconds until the alarm
time display and alarm icon flash. A beep sounds. Release the button.
2. Press the
–
or
+
Buttons
to adjust the alarm time to the desired time
(hold for rapid setting). Make sure you set the correct AM/PM alarm time.
The PM indicator appears to the left of the display.
3. Press the
Sound Alarm Button
to confirm the alarm time setting. The
alarm schedule will flash: 7 (every day), 5 (weekdays) or 2 (weekend
only). Press the
–
or
+
Buttons
to select the desired alarm schedule.
4. Press the
Sound Alarm Button
to confirm the alarm schedule. The
wake-to source will flash.
5. Press the
–
or
+
Buttons to select a wake-to alarm source: Bluetooth
or Tone:
If Wake to Bluetooth
: Press the
Sound Alarm Button
to confirm.
If Wake to Tone
: Press the
Sound Alarm Button
to confirm, then use the
the
–
or
+
Buttons
to select a tone.
6. Press the
Sound Alarm Button
to confirm wake-to source. The alarm
volume will flash. Press the
–
or
+
Buttons
to adjust the alarm volume.
7. Press the
Sound Alarm Button
to confirm alarm volume and exit alarm
setting mode. 2 beeps will confirm alarm setting is complete. The alarm
icon on the display indicates alarm is armed.
1.
Press and hold
the
Light Alarm Button
for 2 seconds until the alarm
time display and alarm icon flash. A beep sounds. Release the button.
2. Press the
–
or
+
Buttons
to adjust the alarm time to the desired time
(hold for rapid setting). Make sure you set the correct AM/PM alarm time.
The PM indicator appears to the left of the display.
3. Press the
Light Alarm Button
to confirm the alarm time setting. The
alarm schedule will flash: 7 (every day), 5 (weekdays) or 2 (weekend
only). Press the
–
or
+
Buttons
to select the desired alarm schedule.
4. Press the
Light Alarm Button
to confirm alarm settings and exit alarm
setting mode. 2 beeps will confirm alarm setting is complete. The alarm
icon on the display indicates alarm is armed.
For light alarm, the unit will ramp up the sunrise light 20 min before the
scheduled alarm time, and gradually increases to 100% brightness over
the course of 20 mins.
SETTING A SOUND ALARM
SETTING A LIGHT ALARM
• Turn on your Bluetooth device and
make it ‘discoverable’ by turning on
Bluetooth mode.
• Press and hold the
Bluetooth Pairing
Button
on the top of the iZBT3 until
the Blueooth Pairing Icon flashes to
indicate the unit is in pairing mode.
• Select ‘iHome iZBT3’ on your device’s
Bluetooth menu to connect!
2. Connecting to Bluetooth
iHome
iZBT3
+
Sound Alarm
Zenergy Preset
Light Alarm
Bluetooth
Pairing
Sound
Therapy
Light
Therapy
Snooze/Display Dimmer
DC
Jack
USB
Charging Port
Time
Set
Sleep
Timer
Settings
- Alarm & Time Set
- Light Brightness
PM Indicator
Snooze
Sound
Alarm
Sleep Timer
Bluetooth Connected
Sound
Therapy
Light Therapy
Light Alarm
Press the
Light Button
repeatedly to cycle through light therapy
modes:
Sunrise Light
Glow
Hue
Day
OFF
Press the
Sound Button
repeatedly to cycle through sound therapy
modes:
Meditate
4-7-8
Zen
Dream
Peace
Trance
Nature
Ocean
River
Storm
Wind Chimes
Air
Drive
Focus
Quiet
Heartbeat
OFF
PROGRAMMABLE THERAPY PRESETS
The unit allows you to store presets to easily access your favorite
light and sound mode combinations.
1. When your preferred sound and light modes are active, press
and hold the
Zenergy Button
to set up a preset.
2. Once set, press the
Zenergy Button
to activate your preset at
any time.
USB CHARGING
usb charging
• Place the unit on a level surface away from sources of direct sunlight
or excessive heat.
• Protect your furniture when placing your unit on a natural wood
and lacquered finish. A cloth or other protective material should be
placed between it and the furniture.
1. Connect the standard end of a USB
cable (not included) to the USB port
on the back of the unit.
2. Connect the other end to the charging
port on your device.
Note: Unit must be connected to a power
outlet in order to charge devices.
MAINTENANCE
To set a sleep timer:
1. Press
the
Sleep Button
as needed to cycle to the desired sleep
timer duration: 120, 90, 60, 30, 15 minutes, or OFF.
2. Press release the
Sleep Button
during Sleep Mode to review the
remaining sleep time.
SETTING A SLEEP TIMER
Auto
Dimmer
Sensor
WARRANTY
WARNING
• Do not ingest the battery, Chemical Burn Hazard. This product
contains a coin/button cell battery. If the coin/button cell battery
is swallowed, it can cause severe internal burns in just 2 hours and
can lead to death.
• Keep new and used batteries away from children. If the battery
compartment does not close securely, stop using the product and
keep it away from children. If you think batteries might have been
swallowed or placed inside any part of the body, seek immediate
medical attention.”
• CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY
AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORD-
ING TO THE INSTRUCTIONS.
- Press for Sunrise Light
- Press & Hold to Set Preset
(Light or Sound modes)
NOTE: Press & Hold to Turn OFF current Light Therapy Mode
NOTE: Press & Hold to Turn OFF current Sound Therapy Mode
