FCC Information
This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
• Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
• NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3 (B)/NMB-3(B)
Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
le dispositif a été évalué à satisfaire l'exigence générale de l'exposition aux rf.
l'appareil peut être utilisé dans des conditions d'exposition portatif sans restriction.
WARNING/DISPOSAL OF UNIT
Do NOT attempt to change the battery. Doing so will void the warranty and could cause injury and damage to your device.
To dispose of the unit, follow the instructions below:
• Never dispose of used batteries/electronics with ordinary solid wastes, since they contain toxic substances.
• Always dispose of used batteries/electronics in accordance with the prevailing community regulations.
• Many electronics retailers now recycle batteries and other electronic components at no charge.
GENERAL BATTERY PRECAUTIONS
• Never use or charge a battery if it appears to be leaking, discolored, deformed, or in any way abnormal.
• Never disassemble the unit or attempt to remove battery as that could cause leakage of alkaline solution or other
electrolytic substances.
• Avoid charging a rechargeable battery when the temperature is not within 5°C - 35°C (41° - 95° Fahrenheit).
• Never expose a battery to any liquid.
• Never expose a battery to excessive heat such as direct sunlight or fire. Never use a battery pack in an unventilated vehicle
where excessive internal temperatures may be encountered.
• Always keep batteries out of the reach of infants and small children.
Printed in China
iAVS1-170420-A
Model: iAVS1
FRONT
BACK
INTERIOR
CONNECTING TO YOUR AMAZON ECHO DOT
Docking Your Amazon Echo Dot
Bedside Stereo Speaker System
Model: iAVS1
for Amazon Echo Dot
QUICK START GUIDE
»
iAVS1
»
USB charging cable
»
Universal voltage adapter
»
Amazon Echo Dot insert
TOP
BOTTOM
Display Dimmer Button
Amazon Echo Dot Dock
Playing Amazon Echo Dot Audio
5
2
1
7
10
3
BACK
DC 12V 2A
8
5
5
6
7
push to open
6
6
RESET
RESET
TEST
TEST
9
10
4
»
Connect the included USB charging cable to the Dot USB Charge Port , then pass the
other end of the cable through the slot and connect to the Echo Dot USB port.
»
Connect the AC power adapter to the DC jack .
»
Align the rear of the Echo Dot (the side with the USB port and Aux Jack) with the
opening in the included insert and place the two into the iAVS1 dock well with the ports
facing the back.
»
Connect the built-in Aux-in cable on the back of the iAVS1 to the Aux jack of your
Echo Dot.
»
You can now “Ask Alexa” to access all the functions of Echo Dot and hear the audio
through the iAVS1.
iAVS1 QSG (English)
Size: 280 x 160 mm (folded: 140 x 160 mm)
Color: print Black and
Material: 260gsm Art Card, 4C
April 20, 2017
BACK
BACK
DC 12V 2A
“Alexa, stop”
“Alexa, mute” or “Alexa, unmute”
“Alexa, set volume to 5”
“Alexa, turn up/down the volume”
Contact Us: 1•800•288•2792
For full warranty and full instructions
visit: www.ihome.com/support
VOLUME CONTROL
USING THE DIMMER BUTTON
»
Use the volume control on the Amazon Echo Dot to adjust the volume to your desired
level.
»
TIP: You can use Alexa voice commands to change volume or stop/pause playback.
»
To dim the clock display, touch the
Dimmer Button
on top of the unit as needed to adjust
the display brightness through 8 levels from High to Off.
»
TIP: Press the + and – Buttons on iAVS1 together during clock setting to switch
display from standard 12 hour to 24 hour display.
1 Clock Setting Button
Press and hold
to start
clock setting. Adjust with
+/– Buttons. Press again
to complete clock setting.
NOTE: Alexa cannot set clock
2 +/– Setting Buttons
3
Press to adjust clock
during setting (hold for
rapid adjust)
4 Backup Battery
Compartment
Unscrew door with Phillips
screwdriver. Insert
2 AAA
batteries (included) as
shown to maintain clock
setting during power
interruption.
5 Dot USB Charge Port
6 Hardwired Aux cable
7 DC Jack
Connect the included AC
adapter to the DC jack
located on the back of the
unit and connect the other
end to a working wall
8 USB Charge Device Port
Connect a standard USB cable
(not included) to charge mobile
devices.
9 Rear Cover
10 AC Adapter
Powering Amazon Echo Dot
DC 12V 2A
DC 12V 2A
5
Amazon, Alexa, Echo Dot and all
related logos are trademarks of
Amazon.com, Inc. or its affiliates.
