Iget SECURITY M3P4 Скачать руководство пользователя страница 1

• 

Working Voltage

DC 3V

• 

Battery

1x CR2032 button battery (3 V)

• 

Working Current

20mA

• 

Standby Current

2μA

• 

Transmission Distance 

Without obstacle 200m

• 

Transmission Frequency

433.29MHz

• 

Working Temperature

-10

~40

• 

Humidity

≤90%rh (non-condensing)

• 

Weight

35.5g(battery not included)     40g(battery included)  

• 

Dimension

Transmitter: 80.0mm*38.2mm*13.3mm  Magnet: 80.0mm*14.8*12.9mm   (L*W*H)

Installation manual 

|

 

Wireless Contact Sensor

Instalační manuál    

|

 

Detektor dveře/okna

Inštalačný manuál   

|

 

Detektor dvere/okná

Website : www.iget.eu E-mail : [email protected]

Battery replacement instructions/ 

Výměna baterie

Výmena batérie

Trigger Mode Clarification/ 

Funkce Trigger

Funkcie Trigger

Trigger Mode Mód Triggeru Mód Triggeru

Clarification

 Význam

Význam

Close

Zavřený

Zatvorený

Deactivated when triggered 

Deaktivován pro všechny režimy alarmu

Deaktivovaný pre všetky režimy alarmu

Instant

Okamžitý

Okamžitý

Activated when ARM/HOME ARM

Aktivní když je režim alarmu Aktivován/

Režim Doma

Aktívny keď je režim alarmu Aktivovaný / 

Režim Doma

24 Hours

24 Hodin

24 Hodín

Activated even when DISARM

Aktivní vždy i při režimu alarmu Deaktivace

Aktívna vždy aj pri režime alarmu 

Deaktivácia

Home

Režim Doma

Režim Doma

Deactivated when DISARM/HOME ARM

Neaktivní pokud je režim alarmu Deaktivace/

Režim Doma

Neaktívne ak je režim alarmu Deaktivácia / 

Režim Doma

Door Chime

Uvítací Gong

Uvítací Gong

No alarm but clanking

Bez alarmu, ale uvítací gong (např. pro 

obchody)

Bez alarmu, ale uvítací gong (napr. pre 

obchody)

Delay

Zpoždění

Oneskorenie

Wait few seconds before alarm

Čeká několik vteřin před aktivací alarmu

Čaká niekoľko sekúnd pred aktiváciou 

alarmu

Insert the flat blade of a small screwdriver into the pry-off slot of transmitter, 

twist the blade to remove the cover.

Stiskněte tlačítko dolů pomocí palce a druhou rukou otevřete kryt detektoru.

Stlačte tlačidlo nadol pomocou palca a druhou rukou otvorte kryt detektora.

Replace with 1x CR2032 battery with the 

plus (+) symbol facing up.

Vyměňte 1xCR2032 baterii, označením plus (+) nahoru.

Vymeňte 2x CR2032 bateriu, označením plus (+) nahor.

Features

Parameters

Appearance

The iGET SECURITY M3P4 wireless contact sensor is an accessory of iGET SECURITY M3/M4 series smart alarm system.It's fashion 
design, energy saving, and low battery warning supported. The main panel will send a SMS to user for battery replacement 
when needed.It's easy to setup and works well with most doors and windows. When transmitter and magnet are apart, the 
sensor triggers alarm. Two great features:
- Transmitter can be put on either of magnet's left or right side.

SECURITY M3P4

LED Indication

Magnet

Transmitter

LED flashes once: 

Door/window is opened and transmitter sends signal to the main panel. 

LED lights stays on: 

Low battery, please replace the battery immediately.

LED Indicator

PCB Layout

Operating Instructions

Installation & Notice

1. Working principle
The transmitter sends trigger signal to main panel paired when the magnet mounted near is moved apart. 
2. Pairing with main panel by App

Scan the QR code printed on the sensor.

The pairing result would be confirmed by SMS sent from main panel.

• Open the case and remove the battery insulative strip.
• Pairing to main panel by App before installing. 
• Attach the transmitter and magnet seperately on door/window and its frame with double-side sticky tape or fix with screws. 
Transmitter can be put on either of magnet's left or right side. 
• Make sure the distance between transmitter and magnet is less than 1cm and at the same level. 
• Avoid installing the sensors in area with a large amount of metal or electric wire.

Less than 1cm

Отзывы: