
Installation manual
|
Wireless Motion Sensor
Instalační manuál
|
Pohybový PIR detektor
Inštalačný manuál
|
Pohybový PIR detektor
Website : www.iget.eu E-mail : [email protected]
Battery replacement instructions/
Výměna baterie
/
Výmena batérie
Trigger Mode Clarification/
Funkce Trigger
/
Funkcie Trigger
Trigger Mode Mód Triggeru Mód Triggeru
Clarification
Význam
Význam
Close
Zavřený
Zatvorený
Deactivated when triggered
Deaktivován pro všechny režimy alarmu
Deaktivovaný pre všetky režimy alarmu
Instant
Okamžitý
Okamžitý
Activated when ARM/HOME ARM
Aktivní když je režim alarmu Aktivován/
Režim Doma
Aktívny keď je režim alarmu Aktivovaný /
Režim Doma
24 Hours
24 Hodin
24 Hodín
Activated even when DISARM
Aktivní vždy i při režimu alarmu Deaktivace
Aktívna vždy aj pri režime alarmu
Deaktivácia
Home
Režim Doma
Režim Doma
Deactivated when DISARM/HOME ARM
Neaktivní pokud je režim alarmu Deaktivace/
Režim Doma
Neaktívne ak je režim alarmu Deaktivácia /
Režim Doma
Door Chime
Uvítací Gong
Uvítací Gong
No alarm but clanking
Bez alarmu, ale uvítací gong (např. pro
obchody)
Bez alarmu, ale uvítací gong (napr. pre
obchody)
Delay
Zpoždění
Oneskorenie
Wait few seconds before alarm
Čeká několik vteřin před aktivací alarmu
Čaká niekoľko sekúnd pred aktiváciou
alarmu
①
Press down the hook on sensor with thumb, push it to open the cover.
①
Stiskněte tlačítko dolů pomocí palce a druhou rukou otevřete kryt detektoru.
①
Stlačte tlačidlo nadol pomocou palca a druhou rukou otvorte kryt detektora.
②
Replace with 2x AA battery.
②
Vyměňte 2x AA baterie.
②
Vymeňte 2x AA batérie.
Operating Instructions
Installation & Notice
1. Working principle
with digital dual-core fuzzy logic operative pro-
gramming and intelligent analysis, it accurately
detects human body movement with infrared
sensor and sends signal to main panel.
2. Pairing with main panel by App
①
Scan the QR code printed on the sensor.
②
The pairing result would be confirmed by SMS
sent from main panel.
• Open the case and remove the battery insulative strip.
• Pairing with main panel by App before installing.
• Fix the bracket with double-side sticky tape or screws on wall, connect the sensor to bracket, adjust a
proper angle. 360° angle adjustment is easily available with connection of bead and magnetic slice.
• Recommended to install at height of 1.8-2.2m from ground, with gradient 10°~20°.
• Indoor use only. Avoid installing the sensors in area with strong light, temperature changes rapidly or
the air stream flows frequently, like close to windows, air conditioner, refrigerator, heater, oven, and
large obstacles.
• Aovid installing two sensors in the same detection scope to interference.
• The sensor is more sensitive to the cross movement than to the vertical movement, so the perference
of sensor is best when the detection direction is vertical to the walking direction of people.
PCB Layout
Detective Interval Time
Setting Switch
(every 5s. or 5min.)
On/Off Switch
Infrared Sensor
10°-20°
1.8-2.2m
Detection blind zone
12m
6m
1.2m
Features
Parameters
Appearance
The M3P1 wireless motion sensor is an accessory of iGET SECURITY M3 series smart alarm system, mainly for indoor use. With
high performance infrared sensor, works under digital dual-core fuzzy logic operative programming and intelligent analysis,
it accurately detects human body movement and effectively avoids false alarms. Featured with automatic temperature
compensation technology, it ensures high intelligence, sensitivity, and stability. It’s fashion design, energy saving, low battery
warning supported and with long transmission distance. The main panel will send a SMS to user for battery changing when
needed. With 360º angle adjustment supported, it’s easy to setup and never get stuck.
•
Working Voltage
DC 3V
•
Battery
2 × AA battery(1.5V)
•
Working Current
22mA
•
Standby Current
60μA
•
Detective Range
110°
•
Detective Distance
9m
•
Transmission Distance
Without obstacle 100m
•
Transmission Frequency
433.29MHz
•
Working Temperature
-10
℃
~40
℃
•
Humidity
≤90%rh (non-condensing)
•
Weight
66g (battery not included) 112g (battery included) 62.3g (Bracket)
•
Dimension
99.6mm*54.0mm*40.2mm L*W*H(±0.1mm)
Detection Window
Magnetic Slice
Trigger Button
Stainless-steel Bead
LED Indicato
r
Bracket
SECURITY M3P1
Exclusive importer of products Shenzhen Dinsafe Intelligence Co., Ltd.
for the Czech Republic and Slovak Republic
INTELEK spol. s.r.o., Vlárská 22, 627 00 Brno
SUPPORT: http: //www.iget.eu/helpdesk
Copyright © 2015 INTELEK spol. s r.o. All rights reserved.