IFM SM6x04 Скачать руководство пользователя страница 19

Страница: 19 / 22

10.4.5 Error behaviour of the outputs

►

Select [FOUx] and set the value:

-On = The analogue signal goes to the upper fault value

(→ 4.3)

�

-OFF = The analogue value goes to the lower fault value

(→ 4.3)

�

-OU = The analogue signal corresponds to the measured value�

10.5 Service functions
10.5.1 Read min/max values

Read minimum or maximum measured values:

►

Select Hi�x or Lo�x�

Hi�F = maximum volumetric flow, Lo�F = minimum volumetric flow

Hi�T = maximum temperature, Lo�T = minimum temperature

Delete memory:

►

Select Hi�x or Lo�x�

►

Press and hold [Set] until [----] is displayed�

►

Briefly press [Mode/Enter]�

It makes sense to delete the memories as soon as the unit operates under normal

operating conditions for the first time�

10.5.2 Restoring the factory settings

►

Select [rES]�

►

Press and hold [Set] until [----] is displayed�

►

Briefly press [Mode/Enter]�

→ 14 Factory setting

� We recommend taking down your own settings in that table

before carrying out a reset�

11 Operation

11.1 Reading the process value

The LEDs 1-6 signal which process value is currently displayed�

The process value to be displayed as standard (volumetric flow quantity or tem-

perature) can be preset

→ 10.4.3 Standard display

�

Moreover, a standard unit of measurement can be defined (volumetric flow

→

10�4�1 and temperature

→ 10.4.2

)�

Содержание SM6x04























Результаты поиска

Содержание SM6x04

Отзывы:

Бренды по названию

Популярные бренды

IFM SM6x04, Руководство по эксплуатации

Результаты поиска

Содержание SM6x04

Отзывы:

Бренды по названию

Популярные бренды