manualshive.com logo in svg

IFM PQ78 Series, Руководство по эксплуатации, Страница: 11 / 19

Поделиться
Скачать
IFM PQ78 Series Скачать руководство пользователя страница 11

11

UK

8.2  Explanation of the menu

SP1/rP1

Upper / lower limit value for system pressure at which OUT1 switches�

FH1/FL1

Upper / lower limit for the acceptable range (monitored by OUT1)�

SP2/rP2

Upper / lower limit value for system pressure at which OUT2 switches�

FH2/FL2

Upper / lower limit for the acceptable range (monitored by OUT2)�

EF

Extended functions / opening of menu level 2�

rES

Restore factory settings�

dS1

Time delay for SP1 / FH1�

dS2

Time delay for SP2 / FH2�

dr1

Time delay for rP1 / FL1�

dr2

Time delay for rP2 / FL2�

ou1

Output function for OUT1:

•  Switching signal for the pressure limit values: hysteresis function [H ��] or 

window function [F ��], either normally open [� no] or normally closed [� nc]�

ou2

Output function for OUT2:

•  Switching signal for the pressure limit values: hysteresis function [H ��] or 

window function [F ��], either normally open [� no] or normally closed [� nc]�

•  Diagnostic signal [ou2] = diA�

uni

Standard unit of measurement for system pressure�

Lo

Maximum value memory for system pressure�

Hi

Minimum value memory for system pressure�

dAP

Damping for the switching outputs�

coF

Manually enter the zero point calibration�

tcoF

Teach zero-point calibration�

diS

Update rate and orientation of the display�

cLor

Colour of the digital display (permanent or alternating with switching status 

OUT1)�

Содержание PQ78 Series




















Отзывы:

Нет отзывов