background image

Cylinder sensor with IO-Link

MK59xx

21

- or –

u

Select [Parameter] > [SSC1.x].

u

[SSC1.x Config. ]Select [Mode] and set [Deactivated].

9.8 Diagnostics

The device provides the following diagnostic information via the IO-Link interface:

Operating hours counter (

Ò

 

/

 24)

Power cycles (

Ò

 

/

 24)

Internal temperature (

Ò

 

/

 24)

Stroke time monitoring (

Ò

 

/

 21)

Switching cycle monitoring (

Ò

 

/

 23)

Magnetic field monitoring (

Ò

 

/

 24)

In addition, diagnostic messages can be output as switching signals via the hardware outputs OUT1
and OUT2. The switching output set for the diagnostic message is switched on in normal operation
(normally closed). If the device detects a diagnostic case, the output will be switched off. The switch
point logic cannot be changed.

Diagnostic cases are:

Timeout 1 → 2

 (

Ò

 Stroke time monitoring 

/

 21)

:

The tolerated time window between the activation of SSC1.1 and the activation of SSC1.2 has
been exceeded or not reached.

Timeout 2 → 1

 (

Ò

 Stroke time monitoring 

/

 21)

The tolerated time window between the activation of SSC1.2 and the activation of SSC1.1 was
exceeded or not reached.

Overflow SCT1.1

 (

Ò

 Switching cycle monitoring 

/

 23)

:

The threshold value for the switching cycles counter SCT1.1 has been reached.

Overflow SCT1.2

 (

Ò

 Switching cycle monitoring 

/

 23)

The threshold value for the switching cycles counter SCT1.2 has been reached.

NoData

 (

Ò

 Magnetic field monitoring 

/

 24)

The magnetic field is too strong or too weak or the magnet is outside the measuring range.

9.8.1 Stroke time monitoring

The stroke time monitoring function monitors the time required by the lifting cylinder to change
between two end positions. The two positions (end position 1 and end position 2) are each signalled
by a switching signal via the switching signal channels SSC1.1 and SSC1.2. 
If more or less time is needed for the position change than set via a tolerance time, the "Timeout"
event will be activated.

Stroke time monitoring can be used, for example, to detect wear on the cylinder, dirt in the application
or low air pressure.

9.8.1.1 Stroke time monitoring parameter setting

The time for changing a piston rod between two end positions can be monitored in both directions of
movement of the lifting cylinder. For this purpose, the sequence of the switching process must be
observed when selecting the parameters:

1 --> 2 : Time between deactivation of SSC1.1 and activation of SSC1.2
2 --> 1 : Time between deactivation of SSC1.2 and activation of SSC1.1

Содержание MK59 Series


































Отзывы: