IFM LR7009 Скачать руководство пользователя

Страница: 31 / 36

Electronic level sensor

LR7009

Indication

Possible cause

Recommended actions

[E.033]

Rod or process connection soiled.

Clean the rod and the process connection, then carry
out a reset.*

Installation conditions were not adhered to.

Observe the notes in "Installation".

Probe length, type of probe or sensitivity (setting to
the medium) is incorrect.

Correct the settings, then carry out a reset.*

[SCx]

Flashing: short circuit in switching output x.

Remove the short circuit.

[SC]

Flashing: short circuit in all switching outputs.

Remove the short circuit.

[PArA]

Faulty data set.

Reset to factory settings.

* Carry out a reset (power off and on again) after rectifying the fault to reset the error message.

10.5 Output response in different operating states

OUT1

OUT2

Initialisation

OFF

Normal operation

according to the level and OU1 setting

according to the level and OU2 setting

Fault (E.0xx)

OFF for FOU1 = OFF;

ON for FOU1 = on

OFF for FOU2 = OFF;

ON for FOU2 = on

Содержание LR7009





































Результаты поиска

Содержание LR7009

Отзывы:

Похожие инструкции для LR7009

Бренды по названию

Популярные бренды

IFM LR7009, Руководство по эксплуатации

Результаты поиска

Содержание LR7009

Отзывы:

Похожие инструкции для LR7009

Бренды по названию

Популярные бренды