IFM FX460 Скачать руководство пользователя страница 47

Страница: 47 / 47

Operating instructions FX460

12 Maintenance, repair and disposal

12.1 Servicing

In case of regular operation, no maintenance measures are necessary for the unit�

In case of unexpected problems, errors or functional failures, the unit must be sent

to the manufacturer to be examined and, if necessary, repaired� Unauthorised

opening and set-up may impair the functioning of the unit or cause failure of the

protective measures supported by the unit�

12.2 Cleaning the housing surface

►

Clean the device from dirt using a soft, chemically untreated cloth�

►

The competent maintenance staff or the corresponding installer is responsible

for unscheduled cleaning�

12.3 Repair

►

The device must only be repaired by the manufacturer�

Observe the safety instructions

(→ 2 Safety instructions)

�

12.4 Disposal

►

Dispose of the device in accordance with the national environmental

regulations�

13 Approvals/standards

Test standards and regulations

(→ 11 Technical data)

EC Declaration of Conformity and approvals are available at www�ifm�com�

Содержание FX460
















































Результаты поиска

Содержание FX460

Отзывы:

Похожие инструкции для FX460

Бренды по названию

Популярные бренды

IFM FX460, Руководство по эксплуатации

Результаты поиска

Содержание FX460

Отзывы:

Похожие инструкции для FX460

Бренды по названию

Популярные бренды