IFM ECOMAT 300 AL1000 Скачать руководство пользователя страница 7

Страница: 7 / 61

IO-Link master

► Devices that are designed for mounting in housings or control cabinets must

only be operated and controlled after they have been installed with the housing

closed� Desktop or portable units must only be operated and controlled in

enclosed housings�

► Measures should be taken to ensure the proper restart of programs interrupted

after a voltage dip or failure� This should not cause dangerous operating states

even for a short time� If necessary, an emergency stop must be carried out�

► Wherever faults in the automation system may cause personal injuries or

damage to property, external measures must be implemented to ensure a safe

operating state in the event of a fault or malfunction (e�g� by means of separate

limit switches, mechanical interlocks etc�)

► The electrical installation must be carried out in accordance with the relevant

regulations (e�g� with regard to cable cross-sections, fuses, PE)�

► All work relating to transport, installation, commissioning and maintenance

must only be carried out by qualified personnel� (IEC 60 364 or HD 384 or

DIN VDE 0100 and national work safety regulations have to be observed)�

► All shrouds and doors must be kept closed during operation�

3 Documentation

This documentation relates to the hardware and firmware status at the time of

editing this manual� The features of the devices are continuously developed further

and improved�

4 Functions and features

The devices have been designed for use in applications described in this manual

and the device-specific data sheets�
Adhere to the data indicated in the data sheets and in the manual� If the handling

specifications and safety instructions for configuration, installation and operation

indicated in the documentation are adhered to, the devices normally do not lead to

a danger for persons and objects�

The input and output devices of the IO-Link master have been designed for

automation tasks in harsh environmental conditions� The devices meet the

requirements of IP65/67 protection rating� They enable direct connection of

sensors and actuators in an environment close to the station�
The devices are available with M12 connection technology�
The devices cannot be extended and have a directly integrated fieldbus

connection and I/O level� They are used for distribution in the field when only a few

digital or analogue I/O points are required�

Содержание ECOMAT 300 AL1000






























































Результаты поиска

Содержание ECOMAT 300 AL1000

Отзывы:

Похожие инструкции для ECOMAT 300 AL1000

Бренды по названию

Популярные бренды

IFM ECOMAT 300 AL1000, Руководство по эксплуатации устройства

Результаты поиска

Содержание ECOMAT 300 AL1000

Отзывы:

Похожие инструкции для ECOMAT 300 AL1000

Бренды по названию

Популярные бренды