IFM Electronic LR2059 Скачать руководство пользователя

Страница: 47 / 51

12.8 Output response in different operating states

OUT1

OUT2*

Initialisation

OFF

Normal operation

according to the level and

[ou1] setting

according to the level 4...20

Fault

OFF for [FOU1] = [OFF]

ON for [FOU1] = [On]

< 3.6 mA at [FOU2] = [OFF]

> 21 mA at [FOU2] = [On]

* If the analogue function [ou2] = [I] has been selected.

If the switching function has been selected: see column OUT1

Additional information about the analogue output:

Full signal: With [ou2] = [I]:

20...20.5 mA

With [ou2] = [InEG]: 4...3.8 mA

Empty signal: With [ou2] = [I]:

4...3.8 mA

With [ou2] = [InEG]: 20...20.5 mA

13 Technical data

Technical data and scale drawing at www.ifm.com

13.1 Setting ranges

[LEnG]

Setting range

150...2000

Step increment

The setting ranges for the switching limits ([SPx], [rPx], [FHx], [FLx]) depend on

the probe length (L). In general the following applies:

min

max

[SPx] / [FHx]

15 (35)

L - 30

[rPx] / [FLx]

10 (30)

L - 35

Step increment

Note: The values in brackets apply to the setting [MEdl] = [LOW) (→ 11.2.3)

• [rPx] / [FLx] is always smaller than [SPx] / [FHx]. If [SPx] / [FHx] is shifted, [rPx ] / [FLx] also

shifts provided that the lower end of the setting range is not reached. Always set [SPx] /

[FHx] first, then [rPx] / [FLx].

Содержание LR2059




















































Результаты поиска

Содержание LR2059

Отзывы:

Похожие инструкции для LR2059

Бренды по названию

Популярные бренды

IFM Electronic LR2059, Руководство по эксплуатации

Результаты поиска

Содержание LR2059

Отзывы:

Похожие инструкции для LR2059

Бренды по названию

Популярные бренды