IFM Electronic LR2059 Скачать руководство пользователя

Страница: 37 / 51

11.2 Basic settings (set-up)

On delivery of the unit, you must first enter the basic settings. The complete user

menu then opens.

11.2.1 Enter type of probe used

►

Apply operating voltage.

> The initial display

is shown.

► Select [Prob] and set:

►

Press [Enter].

> [nonE] is displayed.

►

Press [

▲

] or [

▼

] for min. 1 s and set the value:

[rod] =

Single probe, for the detection of:

-water and water-based media.

[COAX] =

Coaxial probe, for the detection of:

-oils and oil-based media.

-water and water-based media.

►

Press [Enter].

• The detection of water and water-based media is possible with the single

probe as well as with the coaxial probe.

• The detection of oils and oil-based media is only possible with the coaxial

probe.

11.2.2 Enter probe length

►

Select [LEnG].

►

Press [Enter].

> [nonE] is displayed.

►

Press [

▲

] or [

▼

] for at least 1 s.

> After 1 s the unit automatically displays the detected probe length

(preset function*).

►

Correct the probe length, if necessary, with [

▲

] or [

▼

]. Incrementally by

pressing the button once or continuously by keeping the button pressed.

Enter the probe length in mm.

►

Press [Enter].

Automatic probe length detection is only possible with empty tank and sufficiently large

launching plate.

For manual determination of the probe length: (→ 7.5.2)

Содержание LR2059




















































Результаты поиска

Содержание LR2059

Отзывы:

Похожие инструкции для LR2059

Бренды по названию

Популярные бренды

IFM Electronic LR2059, Руководство по эксплуатации

Результаты поиска

Содержание LR2059

Отзывы:

Похожие инструкции для LR2059

Бренды по названию

Популярные бренды